Asus ROG SWIFT PG27U Manual Download Page 31

Page: 31 / 33

3-11

ASUS PG27U Series LCD Monitor

DisplayPort.input--Over.clocking

Resolution.Frequency

Refresh.Rate.

3840 x 2160

144Hz

Note:.

Do.not.support.interlace.

Since.HDR.content.is.aimed.at.4K.(3840.x.2160).resolution,.other.resolution.may.result.in.abnormal.

images.

Please.wait.for.Over.Clocking.function.to.initiate..The.process.may.take.less.than.40.seconds.

Over.Clocking.supported.GPUs:.NVIDIA.Pascal.GPU.Graphics.Card.like.GTX1070,.GTX1080.

and.GTX1080.Ti.or.higher..For.other.GPUs,.please.contact.the.manufactures.to.see.if.they.are.

compatible.

The.monitor.is.purposely.supporting.the.NVIDIA.G-SYNC.technology.and.targeting.NVIDIA.graphics.

solutions.

Please note that Over Clocking function/performance depends on the GPUs,

contents displayed, viewing distance/angle, refresh rate and user eyes

sensitivity. ASUS only provides this function. The performance or any side effect

after activation is not guaranteed. Side effect, such as decayed contrast ratio or

waterfall is not a product defect but trade off.

Summary of Contents for ROG SWIFT PG27U


































Search results

Summary of Contents for ROG SWIFT PG27U

Reviews:

Related manuals for ROG SWIFT PG27U

Brands by name

Popular brands

Asus ROG SWIFT PG27U, Manual

Search results

Summary of Contents for ROG SWIFT PG27U

Reviews:

Related manuals for ROG SWIFT PG27U

Brands by name

Popular brands