Asus AAEON BOXER-6614 User Manual Download Page 89

Page: 89 / 112

Chapter 3

–

AMI BIOS Setup

Fan

les

s E

mb
ed

ded

BO
XE

R-

3.6 Setup submenu: Security

Change User/Administrator Password

You can set an Administrator Password or User Password. An Administrator Password

must be set before you can set a User Password. The password will be required during

boot up, or when the user enters the Setup utility. A User Password does not provide

access to many of the features in the Setup utility.

Select the password you wish to set, and press Enter. In the dialog box, enter your

password (must be between 3 and 20 letters or numbers). Press Enter and retype your

password to confirm. Press Enter again to set the password.

Removing the Password

Select the password you want to remove and enter the current password. At the next

dialog box press Enter to disable password protection.

Summary of Contents for AAEON BOXER-6614

















































































































Search results

Summary of Contents for AAEON BOXER-6614

Reviews:

Related manuals for AAEON BOXER-6614

Brands by name

Popular brands

Asus AAEON BOXER-6614, User Manual

Search results

Summary of Contents for AAEON BOXER-6614

Reviews:

Related manuals for AAEON BOXER-6614

Brands by name

Popular brands