AstroNova QuickLabel QL800 User Manual Download

Page: 29 / 172

Getting Started

QL-800 User Guide

Installing the Printhead

Use the following instructions to install the printhead.

Caution:

The printhead is sensitive to electrostatic discharge (ESD). Use ESD protection

when handling the printhead.

Caution:

Do not touch the printhead cartridge ink couplings, nozzle surface, or the electrical

contacts when installing the printhead cartridge. Hold the printhead cartridge ONLY by the
handles.

Caution:

To avoid drying out the printhead, do not open the printhead packaging until you are

ready to use it.

Caution:

Open the printhead packaging over an appropriate receptacle to safely capture any

excess shipping fluid.

Ensure the printer is powered on and the ink cartridges have been installed.

Open the top cover.

Make sure the printhead latch [1] is in the open (vertical) position. Remove the cap
protectors [2] from the two fluidic couplings.

Note:

The printhead latch will be in the open position. Do not close the latch before

installing the printhead. If the latch is accidentally closed, do not pry it open. Turn the printer
off and back on again. The latch automatically opens during power up if no printhead is
installed.

Remove the printhead from the packaging.

Note:

If the foil packing is damaged, report the issue to Technical Support or your reseller.

Caution:

Do not place the unprotected printhead cartridge on any surface. Protect the

printhead cartridge at all times from contamination such as dust or fibers.

Wipe any excess shipping fluid from the printhead cartridge with a clean, lint-free cloth.

[1]

[2]

Summary of Contents for QuickLabel QL800













































































































































































Search results

Summary of Contents for QuickLabel QL800

Reviews:

Related manuals for QuickLabel QL800

Brands by name

Popular brands

AstroNova QuickLabel QL800, User Manual

Search results

Summary of Contents for QuickLabel QL800

Reviews:

Related manuals for QuickLabel QL800

Brands by name

Popular brands