manualshive.com logo in svg

ASTECH VLM500, User Manual, Page: 27 / 29

Share
Download
ASTECH VLM500 User Manual Download Page 27

Error messages 

 

VLM60 User Manual 

 

ASTECH GmbH 

     page 27 

 

6

 

Error messages 

All  error  messages  start  with  the  letter  'E'  and  a  two-digit  error  number.  The  device  errors  are  divided  into 
different categories, depending on the degree of severity. Critical errors require a change in programming or 
operating conditions in most cases. Fatal errors indicate a serious hardware fault. The device must be checked. 

 

Code 

Meaning 

Cause 

E00 No error 

No error occurred 

- 

E20 Serial console framing error 

Data error during serial 
transmission 

USB error, wrong 
communication parameter 

E21 Serial console parity error 

Parity error during serial 
transmission 

USB error, wrong 
communication parameter 

E22 Serial console overrun error 

Internal buffer overflow 
during serial transmission 

Too much data traffic 

E23 Serial console break error 

Physical break of serial 
transmission 

USB error 

E30 Digital potentiometer I2C error 

Internal hardware error of the 
LED control unit 

Device defective 

E31 Temperature sensor I2C error 

Internal hardware error of the 
temperature monitoring 

Device defective 

E32 EEPROM I2C error 

Internal hardware error of the 
parameter memory 

Device defective 

E40 Power LED startup failed 

LED control unit could not be 
initialized  

Device defective or LED 
defective 

E41 Power LED control error 

LED brightness could not be 
controlled 

Device defective 

E42 Power LED voltage or current fault 

Error in LED brightness 
controlling 

LED defective 

E50 Motion sensor initialization error 

Initialization of primary sensor 
not possible 

Device defective 

E51 Motion sensor configuration error 

Configuration of primary 
sensor not possible 

Device defective 

E52 Motion sensor burst error 

Error during data transmission 
with primary sensor 

Device defective 

E53 Motion sensor frame capture error 

Video mode of primary sensor 
erroneous  

Device defective or device 
restart necessary 

 

 

 

 

 

Summary of Contents for VLM500






























Reviews:

No comments