background image

10

6.  Only PCIE1 slot supports Gen 3 speed. To run the PCI Express in Gen 

3 speed, please install an Ivy Bridge CPU. If you install a Sandy Bridge 
CPU, the PCI Express will run only at PCI Express Gen 2 speed.

7.  The maximum shared memory size is defined by the chipset vendor and 

is subject to change. Please check Intel

®

 website for the latest informa-

tion.

8.  You can choose to use two of the three monitors only. D-Sub, DVI-D and 

HDMI monitors cannot be enabled at the same time. Besides, with the 
DVI-to-HDMI adapter, the DVI-D port can support the same features as 
the HDMI port.

9.  xvYCC and Deep Color are only supported under Windows

®

 7 64-bit / 7. 

Deep Color mode will be enabled only if the display supports 12bpc in 
EDID. HBR audio is supported under Windows

®

 7 64-bit / 7 / Vista

TM

 64-

bit / Vista

TM

.

10.  For microphone input, this motherboard supports both stereo and mono 

modes. For audio output, this motherboard supports 2-channel, 4-chan-
nel, 6-channel, and 8-channel modes. Please check the table on page 14 
for proper connection.

11.  ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to fine-tune 

different system functions in a user-friendly interface, which includes 
Hardware Monitor, Fan Control, Overclocking, OC DNA and IES. In Hard-
ware Monitor, it shows the major readings of your system. In Fan Control, 
it shows the fan speed and temperature for you to adjust. In Overclock-
ing, you are allowed to overclock CPU frequency for optimal system per-
formance. In OC DNA, you can save your OC settings as a profile and 
share  it  with  your  friends. Your  friends  then  can  load  the  OC  profile  to 
their own system to get the same OC settings. In IES (Intelligent Energy 
Saver), the voltage regulator can reduce the number of output phases to 
improve efficiency when the CPU cores are idle without sacrificing com-
puting performance. Please visit our website for the operation procedures 
of ASRock Extreme Tuning Utility (AXTU).

 

ASRock website: http://www.asrock.com

12.  ASRock  Instant  Flash  is  a  BIOS  flash  utility  embedded  in  Flash  ROM. 

This convenient BIOS update tool allows you to update system BIOS 
without entering operating systems first like MS-DOS or Windows

®

. With 

this utility, you can press the <F6> key during the POST or the <F2> 
key to enter into the BIOS setup menu to access ASRock Instant Flash. 
Just launch this tool and save the new BIOS file to your USB flash drive, 
floppy disk or hard drive, then you can update your BIOS only in a few 
clicks without preparing an additional floppy diskette or other complicated 
flash utility. Please be noted that the USB flash drive or hard drive must 
use FAT32/16/12 file system.

13.  If you desire a faster, less restricted way of charging your Apple devices,  

such as iPhone/iPad/iPod Touch, ASRock has prepared a wonderful 
solution for you - ASRock APP Charger. Simply install the APP Charger 
driver, it makes your iPhone charge much quickly from your computer 

Summary of Contents for B75 Pro3





































































Reviews: