LED Corn Light Instruction
Can not use the electric generator to test the LED lamp.
Please avoid using the led fixture in environment where there is smoke,
sulfur, and corrosive substances. But if used in such environment,
make sure the led fixture is well protected by an enclosed lampshade
whose dimension is no less than below size, and whose material is
either glass or semi-glass, semi-metallic. Surface of the lampshade
shall not have any covering which prevents heat dissipation
Power W
Volume CM
110
44*26*26
95
44*24*24
Rev A1
75
47*21*21
ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE-STANDING
PORTABLELUMINAIRE. USE ONLY WITH A PORTABLE LUMINAIRE THAT IS
PROVIDED WITH A SHADE. THIS LAMP EMPLOYS LIGHT EMITTING DIODE
TECHNOLOGY AND UNLIKE TUNGSTEN-HALOGEN LAMPS DOES NOT
REQUIRE A BARRIER. LAMP IS SUITABLE FOR OPEN LUMINAIRES.
NOT FOR EMERGENCY LIGHTING.
ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE STANDING
PORTABLE LUMINAIRE. UTILISER UNIQUEMENT AVEC UNE LAMPE DE TABLE
DOTÉE D’UN ABAT-JOUR. NE CONVIENT PAS AUX SORTIES DE SECOURS.
AVERTISSEMENT:
WARNING:
AVERTISSEMENT - PRECAUTIONNEZ-VOUS CONTRE DES CHOCS ÉLECTRIQUES.
L'INSTALLATION DES PIÈCES DE RECHANGE LED EST SEULEMENT EN CHARGE
DES PROFESSIONNELS. PRECAUTIONNEZ-VOUS CONTRE FEU. INSTALLER DES
PIÈCES DE RECHANGE SELON LES SPÉCIFICATIONS, VEILLER À CE QUE
LA PUISSANCE D'ENTRÉE NE DÉPASSE PAS LA PUISSANCE D'ENTRÉE DE
REMPLACEMENT DE LA LAMPE. NE FAITES PAS DE CONTACT AVEC LE CÂBLE
POINTUS OU MÉTALLIQUES, AFIN D'ÉVITER LE FIL USÉ. VÉRIFIER LE CIRCUIT
FERMÉ, AFIN DE DOMMAGES LES CÂBLES ET LES COMPOSANTS
ÉLECTRONIQUES LORS DE L'INSTALLATION DE FORAGE. NE PAS MODIFIER LA
STRUCTURE DU CIRCUIT FERMÉ ET LES COMPOSANTS ÉLECTRONIQUES OU
FORAGE SUR CELUI-CI LORS DE L'INSTALLATION DES PIÈCES DE RECHANGE.
WARNING – RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLA
-TION REQUIRES KNOWLEDGE OF LUMINARIES ELECTRICAL SYSTEMS. IF NOT
QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRI
-CIAN. WARNING – RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY
IN THE LUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMEN
-SIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS AND WHERE THE
INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING
OF THE LUMINAIRE. WARNING – TO PREVENT WIRING DAMAGE OR ABRASION,
DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP
OBJECTS. WARNING – RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRE WIRING
AND ELECTRICAL PARTS MAY BE DAMAGED WHEN DRILLING FOR INSTALLATION
OF LED RETROFIT KIT. CHECK FOR ENCLOSED WIRING AND COMPONENTS.
DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR
ELECTRICAL COMPONENTS DURING KIT INSTALLATION.THIS RETROFIT KIT IS
ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF
THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING
JURISDICTION. INSTALLERS SHOULD NOT DISCONNECT EXISTING WIRES
FROM LAMPHOLDER TERMINALS TO MAKE 6 CONNECTIONS AT LAMPHOLDER
TERMINALS. INSTEAD INSTALLERS SHOULD CUT EXISTING LAMPHOLDER
LEADS AWAY FROM THE LAMPHOLDER AND MAKE 6 ELECTRICAL
CONNECTIONS TO LAMPHOLDER LEAD WIRES BY EMPLOYING APPLICABLE
CONNECTORS. THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY
EXITS OR NOT FOR EMERGENCY LIGHTING.
