background image

Care and cleaning

Top up rinse aid

When the rinse aid needs topping up, the above symbol lights on the
display.

Press to open

1 Open the rinse aid compartment lid.

2 Carefully top up with rinse aid to the level marked

max

.

3 Wipe up any splashes of rinse aid around the compartment.

4 Close the lid firmly.

After topping up, it may take a while before the symbol goes out.

Top up salt

When the salt needs topping up, the above symbol lights on the display.

Salt compartment lid

When the salt runs out, unscrew the cap and fill the container with salt.
Water is only needed the first time! Wipe clean and tighten. Run a
program to ensure that any salt in the dishwasher is rinsed away.

After topping up, it may take a while before the symbol goes out.

WARNING!

In order to avoid rust stains a dishwashing program must be started
immediately after adding salt.

Never pour dishwasher detergent into the salt compartment. This
destroys the water softener!

Coarse filter

The coarse filter traps larger food particles, which cannot get past the
drainage pump. Empty the coarse filter when necessary.

Coarse filter

1 Lift the coarse filter by the handle.

2 Empty the coarse filter. Remember to refit it!

Fine filter

Debris that collects on the fine filter is automatically rinsed away during
each wash. Clean the fine filter when necessary.

Fine filter

1 Turn the handle anticlockwise.

2 Lift the filter straight up using the handle. Free the coarse filter to

clean the fine filter.

3 Refit in reverse order. Check that the edges seal properly when

refitting the fine filter.

4 Lock the filter in place by turning the handle clockwise to the stop

position. The handle should point straight out from the dishwasher.

NOTE!

Dishwashing results may be

affected if the filters are incorrectly

fitted. Note that the dishwasher

must not be used without the filters

in place.

NOTE!

Check that the coloured stop on

the right in the bottom drain is in

place.

Spray arms

Holes and bearings can sometimes become blocked. Remove any
debris using a pin or something similar. The spray arms also have
holes on their undersides.

To facilitate cleaning, you can remove the spray arms. Remember to
fit them firmly back into place after cleaning.

Upper spray arm

1 Pull out the upper basket.

14

Summary of Contents for DWCBI241





























Reviews: