Dimensions (W x H x D) {inches (mm)}
Soap Tank Capacity {fl oz (ml)}
Battery Type Required
Battery Life Estimated
Detection Range Automatic,
manually adjustable {inches (mm)}
Room Temperature {°F (°C)}
Sensing Delay Time (msec)
Dispensing Volume {fl oz (ml)}
Applicable Viscosity Range {cP(MPas)}
Unit Net Weight empty {oz (kg)}
Operation Mode
Supply Reservoir Types
Pump Type
4.83 x 10.63 x 4.17 (122 x 270 x 106)
30.4 (900)
Alkaline (1.5V) AA size, Qty 4
10,000 cycles or 1 year
2.40 (60) ± 1.50 (38)
41 ~ 104 (5 ~ 40)
500 ~ 1k
0.034 ~ 0.051 (1 ~ 1.5)
2000 ~ 5000
24.7 (0.7)
Automatic from Sensor Trigger
900 ml reusable (included) or 800 ml
disposable (supplied by others)
Peristaltic Tube (self contained valve/nozzle)
1. SPECIFICATIONS:
INSTALLATION INSTRUCTIONS
FOR MODEL N
0362/0363
0610241228
1.Provide vertical, clean and smooth mounting surface.
2.Make sure there is enough room above dispenser to access cover lock key.
3.Ensure there are no obstructions below unit in sensor zone.
4.Check operation of unit while holding in place by hand
permanent installation
BEFORE
3. BEFORE INSTALLATION:
WALL
DISTANCE
COUNTER TOP
DISTANCE (MINIMUM TYPICAL)
At least 7-7/8” (200)
NORMAL COUNTER TOP
STAINLESS STEEL COUNTER TOP
At least 11-13/16” (300)
1. SPECIFICATIONS:
2. ITEM LIST:
4. RECOMMENDED INSTALLATION:
10”
(254)
See No.3
5.2 INSTALLATION STEPS, Adhesive on Mirror
1.Clean mounting surface in area to be installed with isopropyl alcohol.
2.Mark outline of dispenser on mirror with masking tape.
3.Remove paper liners from self-adhesive pads on dispenser backplate.
4.Place unit on mounting surface with even steady pressure and hold for 1 minute.
5.Let tape cure for 10 hours prior to filling dispenser with soap for use.
1.Tape the installation template at the appropriate location on the mounting surface.
2.Drill four (4) holes at marked locations 1
3.Insert four (4) plastic anchors (supplied) into drilled holes; remove template (fig. 1).
4.Insert two (2) screws (supplied) into top plastic anchors and leave 1/8" (3) space from
the wall under head (fig. 2 and fig. 3) for hanging dispenser.
5.Hang the dispenser on the two (2) screws through the keyhole slots at backplate top.
6.Use key to unlock and pull forward the housing cover (fig. 4 )
7.Remove soap reservoir and lock dispenser to wall with remaining two (2) screws
(supplied) through the holes at backplate bottom. Tighten all screws
.
( fig. 5).
/4” diameter (Ø6.4).
5.1 INSTALLATION STEPS, Tile or Dry Wall
Base plate
Soap tank
Key
Lock
Cap
Spout nozzle
Valve tube
Tank cover
Cover
Electronic box
Battery box
Illustration
Illustration
Description
Description
Q’ty
Q’ty
No.
No.
1
2
2
1
3
1
4
4
1set
5
4
1
1
1
1
1
Key on
ring
Installation
Instructions
Installation
Template
Soap
Dispenser
Plastic
Anchor
Items all included in item 4
Mounting
screw
SOAP DISPENSER MOUNTING
TEMPLATE
1/4” (
)
¯
6.4
fig.1
Item 5
Item 6
fig.2
1/8” (3)
fig.3
fig. 4
fig. 5
0610
241228
0
61024
1228
Nut
Gate
Hinge nut
Hinge screw
Retainer
screw
6
7
8
9
10
11
Battery
box
Replacement
soap
tank
Lock
Nut
Repla
cover
only
cement
Repla
electronic
box only
w/o battery
box
cement
S
10”
(254)
RevJ
20Dec1
1
