ashtech Reliance FS/2 Operation Manual Download Page 39

Page: 39 / 186

O
p

erat

ion

Field Operation

The following instructions show you how to set up, configure, and use the Reliance
system in a typical GIS data collection session.

Field Checklist

Before leaving the office to collect GIS data, check the following:

FS/2 batteries charged

FS/2 power management configured

Receiver batteries charged

Receiver battery management configured

Feature and waypoint files uploaded to FS/2

Correct interval entered on datalogging screen for rover

Correct interval used on base station

Base station recording

RTCM broadcasting (if using differential mode)

After completing GIS data collection, check the following:

Receiver off

Exit FAMlog

FS/2 off

Base station recording stopped

Equipment Connections

To connect the equipment:

Install GPS receiver and batteries into the backpack.

Identify the interface cable, (Figure 1.5). Connect the 25-pin connector to the
serial port of the receiver.

Connect the circular 12-pin connector to Port 1 of the FS/2 and the other end to
Port A on the interface cable.

Connect one end of the antenna cable to the ANT connector on the receiver.
Connect the other end of the antenna cable to the antenna. The antenna may be

Summary of Contents for Reliance FS/2



























































































































































































Search results

Summary of Contents for Reliance FS/2

Reviews:

Related manuals for Reliance FS/2

Brands by name

Popular brands

ashtech Reliance FS/2, Operation Manual

Search results

Summary of Contents for Reliance FS/2

Reviews:

Related manuals for Reliance FS/2

Brands by name

Popular brands