Ashly nX 1.52 Operating Manual Download

Page: 56 / 60

Operating Manual - nX, nXe, and nXp Power Amplifiers

Protea DSP Specifications

(nXp models only)

Input Source Selection

Input Source Select Options . . . . .

Analog, Auto

(net, AES3, analog)

Dynamics

Brick Wall Limiter

Threshold

. . . . . . . . . . . . . . . . . . . -20dBu to +20dBu

Ratio . . . . . . . . . . . . . . . . . . . . . infinite

Attack

. . . . . . . . . . . . . . . . . . . . . 0.2ms/dB to 50 ms/dB

Release 5ms/dB to 1000ms/dB

Compressor

Threshold

. . . . . . . . . . . . . . . . . . . -20dBu to +20dBu

Ratio . . . . . . . . . . . . . . . . . . . . . 1.2:1 to infinite

Attack

. . . . . . . . . . . . . . . . . . . . . 0.2ms/dB to 50ms/dB

Release 5ms/dB to 1000ms/dB

Detector. . . . . . . . . . . . . . . . . . . . . Peak/Average

Attenuation Bus. . . . . . . . . . . . . . . 2 available

Metering . . . . . . . . . . . . . . . . . . . . In, Out, Attenuation,

superimpose on graph

Autoleveler

Target Level . . . . . . . . . . . . . . . . . -40dBu to +20dBu

Action

. . . . . . . . . . . . . . . . . . . . .

gentle, normal, aggressive,

user defined

Maximum Gain . . . . . . . . . . . . . . . 0dB to +22dB

Metering . . . . . . . . . . . . . . . . . . . . Input, Gain, Attenuation

Advanced Autoleveler

Controls

Ratio . . . . . . . . . . . . . . . . . . . . . 1.2:1 to 10:1

Threshold Below Target . . . . . . . . -30dB to 0dB

Gain Increase Rate . . . . . . . . . . . . 5ms/dB to 1000ms/dB

Gain Decrease Rate. . . . . . . . . . . . 5ms/dB to 1000ms/dB

Hold Time . . . . . . . . . . . . . . . . . . . 0-6s

Ambient Noise Compensation (Output Only)

Max Gain . . . . . . . . . . . . . . . . . . . -20dB to +20dB

Min/Base Gain . . . . . . . . . . . . . . . -40dB to +20dB

Gain Change Rate . . . . . . . . . . . . . 0.2s/dB to 20s/dB

Link Group . . . . . . . . . . . . . . . . . . 16 available

ANC Input Channel. . . . . . . . . . . . 1-2 or 1-4

Noise Threshold . . . . . . . . . . . . . . -40dBu to +20dBu

Program/Ambient Gain Ratio . . . . 0.3:1 to 3:1

Metering . . . . . . . . . . . . . . . . . . . . Input level, Attenuation,

Average noise

Ducker

Ducking Type . . . . . . . . . . . . . . . . high/low priority, trigger,

filibuster, ducked program

Trigger Threshold

. . . . . . . . . . . . . -80dBu to +20dBu

Ducking Release . . . . . . . . . . . . . . 5ms/dB to 1000ms/dB
Ducking Depth . . . . . . . . . . . . . . . 0dB to -30dB, -

∞

Enable Ducking at Matrix Mixer . Yes

Metering . . . . . . . . . . . . . . . . . . . . Input

Gate

Threshold

. . . . . . . . . . . . . . . . . . . -80dBu to +20dBu

Range . . . . . . . . . . . . . . . . . . . . . off, 100dB to 0dB

Attack

. . . . . . . . . . . . . . . . . . . . . 0.2ms/dB to 50ms/dB

Release 5ms/dB to 1000ms/dB

Metering . . . . . . . . . . . . . . . . . . . . Key Signal, Gate LED

superimpose on graph

Advanced

Gate Controls

Key Engage Enable. . . . . . . . . . . . Yes

Key Frequency . . . . . . . . . . . . . . . 20Hz to 20kHz

Key Bandwidth . . . . . . . . . . . . . . . 0.016 to 3.995 octave

Gain

Gain . . . . . . . . . . . . . . . . . . . . . . . . -50dB to +12dB, off,

polarity invert

Gain w/VCA. . . . . . . . . . . . . . . . . . -50dB to +12dB, off,

polarity invert

Digital VCA Groups . . . . . . . . . . . 4 available

Remote Gain

(Remote RD8C Level Control). . . Enable, Disable

Metering . . . . . . . . . . . . . . . . . . . . RD8C Active LED

WR-5 (neWR-5) Remote Gain . . . 0 to -50dB, Mute

Equalization

31 Band Graphic

Filter Type

. . . . . . . . . . . . . . . . . . constant or proportional Q

Bandwidth . . . . . . . . . . . . . . . . . . 0.499 to 0.25 octave

Cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Continuously variable temperature controlled axial fan(s)

Power Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20A powerCON

(32A powerCON

on 3.04 model only)

Operating Voltage Range (50-60Hz, 85VAC or 170VAC minimum startup)

70-135VAC @110-120VAC, or 140-270VAC @220-240VAC

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32°F-120°F, (0°C-49°C) noncondensing

Unit Dimensions (all models) . . . . . . . . . . . . . . . . . . . . . . . . . . . .19”W x 3.5”H x 16.84”D (483 x 89 x 428mm)

Unit Weight by nX Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4002/8002 21.5lbs (9.75kg), 1.52/3.02 22.0lbs (10kg)

4004/8004 25.2lbs (11.4kg), 1.54/3.04 28.0lbs (12.7kg)

Shipping Dimensions (all models). . . . . . . . . . . . . . . . . . . . . . . . .24.5" x 22" x 5.25" (622mm x 559mm x 133mm)

Shipping Weight by nX Model . . . . . . . . . . . . . . . . . . . . . . . . . . .4002/8002 27.6lbs (12.5kg), 1.52/3.02 28.01lbs (12.8kg)

4004/8004 31.3lbs (14.2kg), 1.54/3.04 34.1lbs (15.5kg)

Safety/Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .cTUVus, CE, FCC Class B, RoHS

Summary of Contents for nX 1.52





























































Search results

Summary of Contents for nX 1.52

Reviews:

Related manuals for nX 1.52

Brands by name

Popular brands

Ashly nX 1.52, Operating Manual

Search results

Summary of Contents for nX 1.52

Reviews:

Related manuals for nX 1.52

Brands by name

Popular brands