background image

 

 

Asetek InRackCDU Installation, Operation & Maintenance Guide  21 

recycling center for glycol or anti-freeze. Alternatively, they may be disposed of in an incinerator or other 
thermal destruction device.)  Do not dump quantities over 1quart into any sewers on the ground or into 
any body of water! Dilute any quantities less than 1 quart by at least 5 to 1 before dumping into sanitary 
sewers.  

After  collecting  the spill, return to  the  spill area with half a bucket of fresh water and rinse area with 
towels and clean water, wringing rinse water back into bucket. Dump this rinse water into a sink drain and 
wring  towels.  Allow  cloth  towels  dry  and  then  wash.  Dry  and  incinerate  paper  towels.  Flush  liquid 
collection equipment with plenty of fresh water to clean.  

Appendix II - CDU Specifications 

Parameter 

Specification 

Dimension (L x W x H) 

73.7cm x 44.4cm x 17.8cm (length is just for cabinet without hoses) 

Weight, including coolant 

CDU Cabinet:  80kg (176.4lbs) 
CDM (pair):   
      42U: 10kg (22.0lbs)   
      48U: 12kg (26.5lbs),  

Facility Water Pressure  

Max:  8.62 bar (125 PSI) 

Facility Flow Rate 

1¼ inch facility hose:  Max 5200 l/h (23 GPM) 
1½ inch facility hose: Max 7900 l/h (35 GPM) 

Cooling capacity is influenced by facility flow rate, max cooling capacity is 
obtained with max facility flow

 

Electrical Requirements 

Power Supply Voltage:  100VAC to 240VAC, 50/60Hz, auto-range 
Connector:  IEC320 C14 (male) 
Power Consumption:  70W Max, 15W Normal Operation 

Electrical Requirements 

Physical Layer:  Copper wire, RJ-45 Connector 
Application Layer:  Web browser interface, SNMP, e-mail alerts & alarms 

 

 

Summary of Contents for InRackCDU






























Reviews: