manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 218

TeleBoss 850 2.06.280_STD User Manual 

 

Page 212 

 

Rev D  

On-board ES (Type 2A) port: 
 

 

 
 
 

EventSensors (Type1) / CCU32/64 (Type1) 
Yes.  Connect sensor to Serial Port I/O1 set to ESBUS mode, with an RS232/ES Bus Adapter (part #4162-010). 
 
PB1 
No 
 
EventSensor (Type2) / ES-CCU32/64 (Type2) 
Yes, connect sensor to on-board ES (Type 2A) port with an ES-CAB8 cable.  If the unit also has a 4SJ expansion 
card installed, then the on-board sensor port is disabled.  Connect the sensor to one of the 4SJ ports instead. 
 
PB2 
Yes, requires the T850 host to be running version 2.06.290 or higher.  Also, a PB2 is  only supported by an on-
board sensor port, so it will not work if connected to a 4SJ expansion card. 
 
SensorJack (Type3) 
No 
 
EventSensor (Type1) sensors cannot be daisy-chained with EventSensor (Type2) sensors; however, you can use 
EventSensor (Type1) sensors connected to Serial Port I/O1 

and

 EventSensor (Type2) sensors connected to any 

sensor port simultaneously.  Just make sure the DIP Switches on all are set so that there are no slotting conflicts. 

 
  

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands