manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 213

TeleBoss 850 2.06.280_STD User Manual 

 

Page 207 

 

 Appendices 

 

User Rights Table 

 
Each command has an associated minimum user right required to execute it.  (Unlike the minimum user rights for 
settings, these cannot be changed for any command; they are hard-coded.)  Here is a list of TeleBoss commands and 
their associated minimum user right numbers and aliases. 
 

Command  Minimum required  

right number and alias 

! 

2 VIEW 

? 

2 VIEW 

access 

3 ADMIN1 

addlf 

3 ADMIN1 

bye 

0 NONE 

bypass         3 ADMIN1 
clear         

3 ADMIN1 

clog          

6 MASTER 

coldstart      6 MASTER 
compress      3 ADMIN1 
count         

3 ADMIN1 

crc           

3 ADMIN1 

default         6 MASTER 
del            

6 MASTER 

delete        

3 ADMIN1 

destroy         6 MASTER 
doalarm 

2 VIEW 

domail         2 VIEW 
dopage         2 VIEW 
dosms 

2 VIEW 

dotrap        

2 VIEW 

dir           

2 VIEW 

duplex         3 ADMIN1 
exec            6 MASTER 
execc           6 MASTER 
exit          

0 NONE 

factory         6 MASTER 
free          

2 VIEW 

ftest          

6 MASTER 

help         

0 NONE 

inits          

6 MASTER 

iprc          

2 VIEW 

ip             

6 MASTER 

kill           

6 MASTER 

logoff        

2 VIEW 

mbyte           6 MASTER 
mfill          

6 MASTER 

modemtalk      

6 MASTER 

mword           6 MASTER 
netstat         6 MASTER 
next          

3 ADMIN1 

ntpq          

2 VIEW 

password 

6 MASTER 

ping          

3 ADMIN1 

post           

6 MASTER 

posterror       6 MASTER 
prt           

3 ADMIN1 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands