manualshive.com logo in svg

Asentria Teleboss 850, User Manual

Share
Download
Asentria Teleboss 850 User Manual Download Page 158

TeleBoss 850 2.06.280_STD User Manual 

 

Page 152 

 

NEC NEAX2400 

 
The T850 collects data from the NEC NEAX2400 by opening a socket on a specific port.  Generally, only the 
Hostname or IP Address of the switch is all that needs to be configured on the T850.  Two other settings on the T850 
that have the same default values as the corresponding settings in the switch: Port and Device Number. In certain 
cases where the switch is not configured to default port and device number, you may have to adjust these either on 
the switch or on the T850 to get IPRC running.  The Device Number ranges from 0 to 3 (default 0 on the unit) and 
controls what kind of data the unit retrieves from the switch; refer to the NEAX2400 SMDR reference manual for 
details. 
 
 

 

TeleBoss 850 - IP Record Collection (IPRC) Setup 

A) IP Record Collection                 [NEC NEAX2400] 

B) Store Collected Data In              [FILE1] 
C) Data Alarm/Filter Enable             [OFF] 
D) Target Name                          [IPRC 1] 

E) Hostname/IP Address                  [] 
F) Port                                 [60010] 

G) Request Period (seconds)             [5] 

H) Device Number                        [0] 

I) Time Stamping                        [OFF] 

 

 

Summary of Contents for Teleboss 850
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands