manualshive.com logo in svg

Asentria TeleBoss 830, User Manual

Share
Download
Asentria TeleBoss 830 User Manual Download Page 116

TeleBoss 830 2.11.370 STD User Manual     

 

Page 116 

 

Alarm Trap Number / Return to Normal Trap Number 

These options set the number to be sent with any SNMP traps for this event.  The default is 511, but the 

trap number can also be set in the range of 1000 

– 1199 as needed. 

 

Alarm Class / Return to Normal Class

  

These options are used to set the class for the alarm.  When one of these options is selected, a list of the 

classes previously defined in the 

Class Table

 is displayed, from which you can select one to be assigned 

to this event. 

 

 

CPE Alarm Settings (Ping Alarms) as accessed via Web UI 

On the Web Interface the CPE settings are called Ping Alarms.  All of the settings to configure Ping Alarms 

can be access from the Device Management Page. 

 

The Event settings as covered in the previous section are in the upper section of the page.  The Device 

settings as described in the Network Settings/

CPE Settings

 section are located in the lower section of the 

page.  On the Web Interface the two menus are conveniently located on the same page. 

 

 

 

 

Reset Event Settings 

The Reset Event Settings are used to configure event actions to be performed after the unit has been 

restarted. These actions would be executed regardless of whether the unit was reset via a restart 

command or by power cycling. 

 

 
TeleBoss 830 - Reset Event Settings 
A) Enable Event                         [OFF] 
B) Event Actions                        [] 
C) Event Message                        [Reset Event] 
D) Event Class                          [Info] 
E) Event Trap Number                    [543] 
F) Delay After Reset (seconds)          [0] 

 

 

Enable Event

  

This is an ON/OFF toggle to enable the Reset Event.  The default setting is OFF. 

 

Summary of Contents for TeleBoss 830






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands