ASA Electronics 0200748A Original User Manual Download | Manualshive

Page: 58 / 66

background image

DDM200 user manual - hardware

Created by: MPuchner 01.2020

version: 9600024A

Original user manual

page 58 of 66

printed: 25.02.2020

AC power supply cable

Plug the AC power supply cable which is already connected inside the cabinet to a 110/230VAC socket or an
apporiate UPS. The power plug might differ depending on your location.

Figure 72

–

connecting AC power supply cable

Ethernet (LAN) cable

Connect the ethernet switch inside the cabinet with a socket of your LAN. You can use any available connector
on the ethernet switch. Therefor a Cat5e cable is included.

Figure 73 - connecting ethernet switch

«
...
56
57
58
59
60
...
»

Summary of Contents for 0200748A



































































Reviews:

No comments

Related manuals for 0200748A

Brand: Lamtec Pages: 40

Brand: D+H Pages: 20

Brand: IBM Pages: 54

Brand: ANSMANN Pages: 51

Brand: gefran Pages: 40

Brand: SOMFY Pages: 2

Dexxo Compact RTS

Brand: SOMFY Pages: 10

Brand: SOMFY Pages: 78

Brand: Becker Pages: 20

Brand: WEG Pages: 191

Brand: HAUTAU Pages: 12

Redi-Flo Series

Brand: Grundfos Pages: 16

Brand: Simu Pages: 24

Brand: Rexnord Pages: 7

Brand: Binks Pages: 24

T-Verter N2-220V

Brand: Taian Pages: 80

Brand: Fagor Pages: 118

Brand: IBM Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands