manualshive.com logo in svg

Artison 75340-1, User Manual, Page: 158 / 482

Share
Download
Artison 75340-1 User Manual Download Page 158

Publication No. 980938  Rev. K    

 

Model T940 User Manual 

Astronics Test Systems 

 

Soft Front Panel Operation  5-77 

2.  Idle/Standby Timing  

Phase/Window Spanning 

Phase/Window spanning allows the user to Assert/Open the timing signal in one 
pattern and Return/Close the signal in a different pattern.  The following steps 
describe how to span timing signals across multiple patterns: 

1.  Disable the Return signal in the first pattern’s timing set by setting the 

Return value equal to the pattern period. 

2.  Disable the Assert and Return signal in any patterns between the first and 

the last pattern being spanned by setting the Assert Value to zero and the 
Return value equal to the pattern period. 

3.  Disable the Assert signal in the last pattern by setting the Assert Value to 

zero. 

For example, let’s assume we have three patterns and each pattern has a period 
of 100.  We want the Phase 1 Assert at 50 of the first pattern and Return at 75 of 
the third pattern. 

Pattern 1, TS1 = Assert 50, Return 100 

Pattern 2, TS2 = Assert 0, Return 100 

Pattern 3, TS3 = Assert 0, Return 75 

Idle/Standby Timing 

One of the unique features of the DRM is the Idle/Standby state.  After the 
execution of a sequence burst, the sequencer will enter the Idle/Standby state.  
The user can define the Idle/Standby state timing and pattern such that UUT 
stimulus can be maintained between pattern bursts.  A single pattern can be 
specified so that the pattern memory can be updated (Standby) or a group of 
patterns can be specified (Idle) during this state. 

The user can disable the timing set phases/windows during the Idle/Standby 
state by setting Assert/Return and Open/Close values to zero. 

Editing the Patterns  

Patterns are the memory element that contains the instructions for each channel 
during a sequence burst.  These instructions, called pattern codes, define 
whether a channel will drive high, drive low, test high, etc. 

Once a sequence step has been initialized, a pattern set is assigned to the step.  
A 

Pattern Set

 is one or more patterns.  A 

Pattern

 is the pattern codes for all the 

channels that will be applied at the same time.  (See 

Patterns

 in 

Chapter 5

.) 

Access this panel from the menu bar: 

Edit > Data Sequencer x > Patterns

.  

(Where “x” is the sequencer you wish to configure.) 

Summary of Contents for 75340-1



































































































































































































































































































































































































































































































Reviews:

No comments