manualshive.com logo in svg

Artesyn MITX-CORE-820, Installation And Use Manual, Page: 24 / 133

Share
Download
Artesyn MITX-CORE-820 Installation And Use Manual Download Page 24

MITX-CORE-820 Installation and Use (6806800M10H)

23

Safety Notes

This section provides warnings that precede potentially dangerous procedures throughout 
this manual. Instructions contained in the warnings must be followed during all phases of 
operation, service, and repair of this equipment. You should also employ all other safety 
precautions necessary for the operation of the equipment in your operating environment. 
Failure to comply with these precautions or with specific warnings elsewhere in this manual 
could result in personal injury or damage to the equipment.

Artesyn intends to provide all necessary information to install and handle the product in this 
manual. Because of the complexity of this product and its various uses, we do not guarantee 
that the given information is complete. If you need additional information, ask your Artesyn 
representative.

The product has been designed to meet the standard industrial safety requirements. It must 
only be used in its specific area of office telecommunication industry, industrial control, and 
development. It must not be used in safety critical components, life supporting devices or on 
aircraft.

Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering 
are authorized to install, remove or maintain the product. The information given in this manual 
is meant to complete the knowledge of a specialist and must not be used as replacement for 
qualified personnel.

Keep away from live circuits inside the equipment. Operating personnel must not remove 
equipment covers. Only factory authorized service personnel or other qualified service 
personnel is allowed to remove equipment covers for internal subassembly or component 
replacement or any internal adjustment.

Do not install substitute parts or perform any unauthorized modification of the equipment or 
the warranty may be voided. Contact your local Artesyn representative for service and repair 
to make sure that all safety features are maintained.

Artesyn and our suppliers take significant steps to make sure that there are no bent pins on the 
backplane or connector damage to the boards prior to leaving the factory. Bent pins caused by 
improper installation or by inserting boards with damaged connectors could void the Artesyn 
warranty for the backplane or boards.

This product operates with dangerous voltages that can cause injury or death. Use extreme 
caution when handling, testing, and adjusting this equipment and its components.

Summary of Contents for MITX-CORE-820






































































































































Reviews:

No comments