manualshive.com logo in svg

ARTERY AT32WB415 Series, Reference Manual

Share
Download
ARTERY AT32WB415 Series Reference Manual Download Page 340

  AT32WB415

 

Series  Reference  Manual

 

2022.04.13

 

Page 340 

 

Ver 2.00

 

Device mode: 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 25  Reserved 

0x00 

resd 

Kept at its defaut value. 

Bit 24: 21  FN 

0x0 

ro 

Frame number 
Indicates the least significant 4 bits of the frame number of 
the  data  packet  received  on  the  USB  bus.  This  field  is 
applicable only when the synchronous OUT endpoints are 
supported. 

Bit 20: 17  PKTSTS 

0x0 

ro 

Packet status 
Indicates the status of the received data packet. 
0001: Global OUT NAK (triggers an interrupt) 
0010: OUT data packet received 
0011

: 

OUT transfer completed (triggers an interrupt) 

0100: SETUP transaction completed (triggers an interrupt) 
0110: SETUP data packet received 
Others: Reserved

 

Bit 16: 15  DPID 

0x0 

ro 

Data PID 
Indicates the data PID of the received OUT data packet. 
00: DATA0 
10: DATA1 
01: DATA2 
11: MDATA

 

Bit 14: 4 

BCNT 

0x000 

ro 

Byte count 
Indicates the byte count of the received data packet. 

Bit 3: 0 

EPTNUM 

0x0 

ro 

Endpoint number 
Indicates  the  endpoint  number  to  which  the  currently 
received data packet belongs.

 

20.6.3.9  OTGFS receive FIFO size register (OTGFS_GRXFSIZ) 

The application can program the SRAM size that must be allocated to the receive FIFO. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 16  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 15: 0 

RXFDEP 

0x0200 

ro/rw 

RxFIFO Depth 
This value is in terms of 32-bit words. 
Minimum value is 16 
Maximum value is 512 
The power-on reset value of this register is defined as the 
largest receive data FIFO depth durig the configuration. 

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands