ARTERY AT32WB415 Series Reference Manual Download Page 131 | Manualshive

Page: 131 / 374

background image

AT32WB415

Series Reference Manual

2022.04.13

Page 131

Ver 2.00

11.5.6 Status register1 (I2C_STS1)

Bit

Register

Reset value

Type

Description

Bit 15

ALERTF

0x0

rw0c

SMBus alert flag
In SMBus host mode:
0: No SMBus alert
1: SMBus alert event is received.
In SMBus slave mode:
It indicates the receiving status of the default device
address (0001100x)
0: Default device address is not received.
1: Default device address is received.
This bit is cleared by software, or by hardware when
I2CEN=0.

Bit 14

TMOUT

0x0

rw0c

SMBus timeout flag
0: No timeout error.
1: Timeout
This  bit  is  cleared  by  software,  or  by  hardware  when
I2CEN=0.
Note: This function is valid only in SMBUS mode.

Bit 13

Reserved

0x0

resd

Kept at its default value.

Bit 12

PECERR

0x0

rw0c

PEC receive error flag
0: No PEC error
1: PEC error occurs.
This bit is cleared by software.

Bit 11

OUF

0x0

rw0c

Overload / underload flag
In transmission mode:
0: Normal
1: Underload
In reception mode:
0: Normal
1: Overload
This bit is cleared by software, or by hardware when
I2CEN=0.

Bit 10

ACKFAIL

0x0

rw0c

Acknowledge failure flag
0: No acknowledge failure
1: Acknowledge failure occurs.
Set by hardware when no acknowledge is returned.
This bit is cleared by software, or by hardware when
I2CEN=0.

Bit 9

ARLOST

0x0

rw0c

Arbitration lost flag
0: No arbitration lost is detected.
1: Arbitration lost is detected.
This bit is cleared by software, or by hardware when
I2CEN=0.
On ARLOST even, the I

2

C interface switches to slave

mode automatically.

Bit 8

BUSERR

0x0

rw0c

Bus error flag
0: No Bus error occurs.
1: Bus error occurs.
Set by hardware when the interface detects a misplaced
Start or Stop condition.
This bit is cleared by software, or by hardware when
I2CEN=0.

Bit 7

TDBE

0x0

ro

Transmit data buffer empty flag

«
...
129
130
131
132
133
...
»

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32WB415 Series

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Brand: Above All Pages: 4

Brand: BARKO LOADERS Pages: 85

SimMan 3G Trauma

Brand: laerdal Pages: 16

Brand: laerdal Pages: 16

Brand: laerdal Pages: 60

Brand: laerdal Pages: 4

Resusci Anne Simulator

Brand: laerdal Pages: 8

Nursing Baby VitalSim

Brand: laerdal Pages: 15

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Bathomatic Basic

Brand: Unique Automation Pages: 10

Brand: Additel Pages: 139

Brand: Xaoc Devices Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands