ARTERY AT32WB415 Series Reference Manual Download Page 127

Page: 127 / 374

AT32WB415

Series Reference Manual

2022.04.13

Page 127

Ver 2.00

11.4.5 I

C interrupt requests

The following table lists all the I

C interrupt requests.

Interrupt event

Event flag

Enable control bit

Start condition sent (Host)

STARTF

EVTIEN

Address sent (host) or address matched (slave)

ADDR7F

10-bit address head sent (host)

ADDRHF

Data transfer complete

TDC

Stop condition received (slave)

STOPF

Transmit data buffer empty

TDBE

EVTIEN and

DATAIEN

Receive data buffer full

RDBF

SMBus alert

ALERTF

ERRIEN

Timeout error

TMOUT

PEC error

PECERR

Overload/underload

OUF

Acknowledge failure

ACKFAIL

Arbitration lost

ARLOST

Bus error

BUSERR

11.4.6 I

C debug mode

When the microcontroller enters debug mode (Cortex

-M4 halted), the SMBUS timeout either continues

to work or stops, depending on the I2Cx_SMBUS_TIMEOUT configuration bit in the DEBUG module.

11.5 I

C registers

These peripheral registers must be accessed by words (32 bits).

Table 11-1 I

C register map and reset values

Register

Offset

Reset value

I2C_CTRL1

0x00

0x0000

I2C_CTRL2

0x04

0x0000

I2C_OADDR1

0x08

0x0000

I2C_OADDR2

0x0C

0x0000

I2C_DT

0x10

0x0000

I2C_STS1

0x14

0x0000

I2C_STS2

0x18

0x0000

I2C_CLKCTRL

0x1C

0x0000

I2C_TMRISE

0x20

0x0002

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Search results

Summary of Contents for AT32WB415 Series

Reviews:

Related manuals for AT32WB415 Series

Brands by name

Popular brands

ARTERY AT32WB415 Series, Reference Manual

Search results

Summary of Contents for AT32WB415 Series

Reviews:

Related manuals for AT32WB415 Series

Brands by name

Popular brands