manualshive.com logo in svg

ARTERY AT32F425 Series, Reference Manual

Share
Download
ARTERY AT32F425 Series Reference Manual Download Page 386

  AT32F425

 

Series  Reference  Manual

 

2022.03.30

 

Page 386 

 

Ver 2.01

 

20.6.3.3  OTGFS AHB configuration register (OTGFS_GAHBCFG) 

This register is used to configure the controller after power-on or mode change. This register mainly 
contains  AHB-related  parameters.  Do  not  change  this  register  after  the  initial  configuration.  The 
application must configure this register before starting transmission on either the AHB or USB. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 9 

Reserved 

0x000000 

resd 

Kept at its default value. 

Bit 8 

PTXFEMPLVL 

0x0 

rw 

Accesible in host mode only 
Periodic TxFIFO empty level 
It indicates when the periodic TxFIFO empty interrupt bit in 
the GINTSTS register is triggered. 
0:  PTXFEMP  (GINTSTS)  interrupt  indicates  that  the 
periodic TxFIFO is half empty 
1:  PTXFEMP  (GINTSTS)  interrupt  indicates  that  the 
periodic TxFIFO is fully empty 

Bit 7 

NPTXFEMPLVL 

0x0 

rw 

Accesible in both host mode and device modes 
Non-Periodic TxFIFO empty level 
In  host  mode,  this  bit  indicates  when  the  non-periodic 
TxFIFO  empty  interrupt  (NPTXFEMP  in  GINTSTS)  is 
triggered. 
In  device  mode,  this  bit  indicates  when  the  IN  endpoint 
TxFIFO  empty  interrupt  (TXFEMP  bit  in  DIEPINTn)  is 
triggered. 
0: The TxFEMP (in DIEPINTn) interrupt indicates that the 

IN endpoint TxFIFO is half empty 

1: The TxFEMP (in DIEPINTn) interrupt indicates that the 
IN endpoint TxFIFO is fully empty 

Bit 6: 1 

Reserved 

0x00 

resd 

Kept at its default value. 

Bit 0 

GLBINTMSK 

0x0 

rw 

Accesible in both host mode and device modes 
Global interrupt mask 
The  application  uses  this  bit  to  mask  or  unmask  the 
interrupts sent by the interrupt line to itself. 
0: Mask the interrupts sent to the application 
1: Unmask the interrupts sent to the application 

20.6.3.4  OTGFS USB configuration register (OTGFS_GUSBCFG) 

This register is used to configure the controller after power-on or a change between host mode and 
device  mode.  This  register  contains  USB  and  USB-PHY  related  parameters.  The  application  must 
program the register before handling any transaction on either the AHB or USB. Do not change this 
register after the initial configuration. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31 

COTXPKT 

0x0 

rw 

Accesible in both host mode and device modes 
Corrupt Tx packet 
This bit is for debug purpose only. Do not set this bit to 1. 

Bit 30 

FDEVMODE 

0x0 

rw 

Accesible in both host mode and device modes 
Force device mode 
Writing 1 to this bit forces the controller to go into device 
mode, irrespective of the status of the ID input poin. 
0: Normal mode 
1: Force device mode 
After setting this bit, the application must wait at least 25ms 
before the configuration takes effect. 

Bit 29 

FHSTMODE 

0x0 

rw 

Accesible in both host mode and device modes 
Force host mode 
Writing  1  to  this  bit  forces  the  controller  to  go  into  host 
mode, irrespective of the status of the ID input poin. 
0: Normal mode 
1: Force host mode 
After setting this bit, the application must wait at least 25ms 
before the configuration takes effect.

 

Bit 28: 15  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 14 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 13: 10  USBTRDTIM 

0x5 

rw 

Accesible in device mode 

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands