ARTERY AT32F425 Series Reference Manual Download Page 189 | Manualshive

Page: 189 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 189

Ver 2.01

0: Period buffer is disabled.
1: Period buffer is enabled.

Bit 6: 4

Reserved

0x0

resd

Kept at its default value.

Bit 3

OCMEN

0x0

rw

One cycle mode enable
This bit is used to select whether to stop the counter at
update event.
0: Disabled
1: Enabled

Bit 2

OVFS

0x0

rw

Overflow event source
This  bit  is  used  to  configure  overflow  event  or  DMA
request sources.
0: Counter overflow, setting the OVFSWTR bit or overflow
event generated from the slave controller
1: Only counter overflow generates an overflow event.

Bit 1

OVFEN

0x0

rw

Overflow event enable
This bit is used to enable or disable OEV event
generation.
0: OEV event is enabled. An overflow event is generated
by any of the following events:

- Counter overflow
- Setting the OVFSWTR bit
- Overflow event generated from the slave controller

1: OEV event is disabled.
If the OVFSWTR bit is set, or a hardware reset is
generated from the slave controller, the counter and the
prescaler are reinitialized.
Note: This bit is set and cleared by software.

Bit 0

TMREN

0x0

rw

TMR enable
0: Disabled
1: Enabled

14.1.4.2 TMR6 and TMR7 control register2 (TMRx_CTRL2)

Bit

Register

Reset value

Type

Description

Bit 15: 7

Reserved

0x000

resd

Kept at its default value.

Bit 6: 4

PTOS

0x0

rw

Master TMR output selection
This field is used to select the signals in master mode to
be sent to slave timers.
000: Reset
001: Enable
010: Update

Bit 3: 0

Reserved

0x0

resd

Kept at its default value.

14.1.4.3 TMR6 and TMR7 DMA/interrupt enable register (TMRx_IDEN)

Bit

Register

Reset value

Type

Description

Bit 15: 9

Reserved

0x00

resd

Kept at its default value.

Bit 8

OVFDEN

0x0

rw

Overflow event DMA request enable

0: Disabled

1: Enabled

Bit 7: 1

Reserved

0x00

resd

Kept at its default value.

Bit 0

OVFIEN

0x0

rw

Overflow interrupt enable

0: Disabled

1: Enabled

14.1.4.4 TMR6 and TMR7 interrupt status register (TMRx_ISTS)

Bit

Register

Reset value

Type

Description

Bit 15: 1

Reserved

0x0000

resd

Kept at its default value.

Bit 0

OVFIF

0x0

rw0c

Overflow interrupt flag
This bit is set by hardware at an update event. It is
cleared by software.
0: No update event occurs.

«
...
187
188
189
190
191
...
»

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

Brand: TC Electronic Pages: 2

Brand: Raritan Pages: 4

Brand: Telit Wireless Solutions Pages: 113

Momentum ROG Strix X570-E D-RGB

Brand: EK-Quantum Pages: 10

Brand: TANDBERG Pages: 3

Brand: M86 Security Pages: 309

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

Brand: V-Count Pages: 2

DataFire GO! PRO

Brand: Digi Pages: 20

AdvancedTCA AT8901M

Brand: Kontron Pages: 76

Brand: ICP Pages: 111

Brand: Transition Networks Pages: 1

Brand: XMOS Pages: 8

Brand: Rosewill Pages: 5

Brand: Yeastar Technology Pages: 2

Ultra Wireless AWN-8030

Brand: Adaptec Pages: 57

BD7682FJ-EVK-301

Brand: Rohm Pages: 6

NVR52A16-16P-4KS2

Brand: Dahua Technology Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands