ARS Automation FlexiBowl 350 Instructions For Use Manual Download Page 73

Page: 73 / 84

7-15

FlexiBowl - models 350 - 500 - 650 - 800

CHAPTER 7 - Maintenance

7.3.4 Replacing the shaker

REPLACING THE SHAKER

Operator qualification

Mechanical maintenance technician

PPE required

Tools/Products to be used

• Allen key
• Loctite 243

CAUTiOn!

Disconnect the power supply before taking the cover off.

Following a visual inspection, if the rubber mounts and screws in the top part of the cylinder are worn, the shaker must
be replaced. Proceed as follows to

replace the unit

Step

Action

Picture

Unplug the power cable from the control panel.

Take the cover off the FlexiBowl

Unscrew the two grub screws

(A)

so that the bar

(B)

can be removed.

Pull the bar out

(B)

Unscrew the screws

(C)

Remove the unit and replace it.

iMPORTAnT!

Always use LOCTITE 243 threadlocker to ensure the screws are properly secured.

Summary of Contents for FlexiBowl 350





















































































Search results

Summary of Contents for FlexiBowl 350

Reviews:

Related manuals for FlexiBowl 350

Brands by name

Popular brands

ARS Automation FlexiBowl 350, Instructions For Use Manual

Search results

Summary of Contents for FlexiBowl 350

Reviews:

Related manuals for FlexiBowl 350

Brands by name

Popular brands