background image

1

REV 1  

04/18/2019

P-3243

P-

3243

ARNOTT

AIR SUSPENSION COMPRESSOR

2013-2019 CADILLAC XTS (EPSILON II)

WARNING:

 

The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved 

and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system. 

Always wear standard hand, ear, and eye protection when servicing the air suspension system.  

Congratulations on your purchase of an Arnott

®

 air suspension product.  We at Arnott Incorporated are proud 

to offer a high quality product at the industry’s most competitive pricing. Thank you for your confidence in us 

and our product.

Proper installation is essential to experience and appreciate the benefits of this system.  Please take a moment 

to review these installation instructions before you begin to install these components on your vehicle. The 

removal and installation of air suspension products should only be performed by a fully qualified, ASE 

Certified, professional.

It is equally important to be aware of all necessary safety measures while installing your new Air Suspension 

System.  This includes proper lifting and immobilizing of the vehicle and isolation of any stored energy to 

prevent personal injury or property damage.

"Engineered to Ride, Built to Last

"

Arnott

®

 is committed to the quality of its products. If you have a question or problem with any Arnott product, 

please contact Arnott by calling 800-251-8993 during normal business hours or email [email protected].

(In the EU  please call +31 (0)73 7850 580 or email [email protected])

Summary of Contents for P-3243









Reviews: