Armytek Optoelectronics Partner A1, User Manual

Page: 1 / 2

Specifications
Thank you for choosing the products of Armytek Optoelectronics Inc., Canada.
Please read this manual carefully before using the flashlight.
USER MANUAL
THE MOST TECHNICALLY ADVANCED
Warnings
Specifications are subject to change without notice.
Armytek Optoelectronics Inc.
Web: www.armytek.com Email: service@armytek.com
Address: 13-85 West Wilmot St, Richmond Hill, Ontario, L4B 1K7, Canada
Partner
Model Partner A1 Partner A2 Partner C1 Partner C2 Partner C4
LED / Optics
Cree XP-L or XM-L2 / TIR
Brightness stabilization type FULL (constant light) DIGITAL (CPU
brightness control) FULL (constant
light)
Light output, LED / OTF lumens* 600 / 500 85 0 / 700 80 0 / 650 1250 / 1050 1450 / 1200
Peak beam intensity, candelas 3280 5080 4320 7560 9360
Hotspot / spill 20 ° / 8 0°
Beam distance* 115 meters 143 meters 131 meters 174 meters 193 meters
Modes, light output
(OTF lumens*) and
runtimes (measured
with Sanyo Eneloop AA
2000 mAh / Armytek
CR123A 1500 mAh /
Armytek 18650 Li-Ion
3400 mAh
until the light
output drops to 10% of
the initial value
)
Turbo 500 lm / 0.8h 7 00 lm / 0.8h 650 lm / 0.7h 1050 lm / 1.5h 1200 lm / 1.7h
Main3 95 lm / 4.2h 95 lm / 8.3h 95 lm / 6.2h 410 lm / 3.8h 410 lm / 6h
Main2 34 lm / 11.7h 34 lm / 25h 34 lm / 18h 190 lm / 9h 190 lm / 17h
Main1
10 lm / 35h 10 lm / 75h 10 lm / 55h 32 lm / 48h 32 lm / 70 h
Firefly 2 lm / 8d 2 lm / 17d 2 lm / 13d 2.5 lm / 18d 2.5 lm / 30d
Strobe 15Hz/ 500lm/ 1.7h 15Hz/ 700lm/ 1.7h 15Hz/ 650lm/ 1.7h 15Hz/ 1050lm/ 3h 15Hz/ 1200lm/ 3.3h
Power source 1xAA /
1x14500 Li-Ion 2xAA 1x18350 Li-Ion /
1xR123 Li-Ion /
1xCR123A 1x18650 Li-Ion /
2xCR123A /
2xR123 Li-Ion 2x18650 Li-Ion /
4xCR123A /
4xR123 Li-Ion
Size and weight (without
batteries) Length 10 4 mm,
body diameter
2
5 . 4 mm, head
diameter 24.5mm,
weight
59 g
Length 1 50 mm,
body diameter
2
5 . 4 mm, head
diameter 24.5mm,
weight 66g
Length 88 mm,
body diameter
2
5 . 4 mm, head
diameter 24.5mm,
weight
55 g
Length 1 1 9mm,
body diameter
2
5 . 4 mm, head
diameter 24.5mm,
weight
61 g
Length 188mm,
body diameter
2
5 . 4 mm, head
diameter 24.5mm,
weight 72g
Armytek Optoelectronics Inc. is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your
needs. The components made in the USA and Japan. . 10 years no-hassle warranty
§
Amazing brightness in four different sizes and with various power sources .
§
Extreme beam distance for such a compact tactical light.
§
TIR-optics for smooth light beam without sharp edges. No «tunnel vision» effect after continuous use.
§
Solid and impact-resistant body ensures the flashlights’ efficiency even after the fallings from the height of 10 meters and harsh
impacts.
§
The highest standard of water- and dustproof IP68 – submersion to the depth up to 10 meters.
§
Compact size and small weight perfect for constant carrying in the bag, pocket or on the belt.
§
Compatible with original remote switches and weapon mounts.
We DO NOT RECOMMEND to use LOW-QUALITY CR123A batteries as a power source for often and continuous flashlight’s
operation. Remember that old or low-quality disposal batteries can be damaged under heavy load and explode.
* Light output for flashlights with Warm light are about 7% less, beam distances are about 3% less.
1. Always follow the instructions from this manual and recommendations on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not use different power sources together, i.e. old ones with new ones, charged with
discharged. Do not use different types of batteries combined as the element with less
capacity can be damaged.
5.
Do not modify or recast the flashlight and its components as it will deprive you of the
warranty.
6. Do not allow water or any other liquid to leak into the flashlight.
7. Do not aim a switched-on flashlight at people's or animals' eyes – it can cause temporary
blindness.
8. Do not allow children to use the flashlight without your assistance.
The producer will not be liable for any harm done to the user if it was caused by
improper use of the product.
Care and Storage
Service and Warranty
Do not disassemble the flashlight except for unscrewing the thread ring gage and replacing the rubber button. There are no
other parts in the flashlight that can be replaced by the user.
It is recommended to clean the threads and O-ring s off dirt and old grease once or twice per year. Remember that reliable protection
from water and dust cannot be provided by worn out sealing. The fouling as well as lack of lubricant cause fast wear-out of threads and
sealing rings. To clean the threads do the following:
1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).
2.
Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged
replace it by a new one.
3. Clean the metal threads with a brush using ethanol. Be careful not to allow the applied liquid to get inside the flashlight or tailcap as
it can cause fails in functionality of the flashlight.
After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G.The application of
automotive and other improper grease can cause swelling and damage of the sealing rings.
In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts
as often as required.
Armytek provides free warranty repair for 10 years (excluding batteries, chargers, switches and connectors which have 2 years
warranty) from the date of buy with the document confirming the purchase.
Guarantee does not extend to damage during:
1. Improper usage.
2. Attempts to modify or repair the flashlight by nonqualified specialists.
3. Longtime application in chlorinated or polluted water, or other liquids (other than water).
4. High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).
5. Usage of low-quality batteries.
In case the rubber button is damaged, it should be replaced. You can also replace the switch with
the spring in the same way.
Replacement order:
1. Unscrew the tailcap.
2. Unscrew the first washer inside it to take out the switch. To do so you should use needle-
nose pliers (round-nose pliers or another tool, the most suitable will be expansion pliers).
Use the tool as it is shown at the picture. To replace the rubber button unscrew the second
washer under the switch.
3. Replace the rubber button and assemble the parts in inverse sequence.