manualshive.com logo in svg

ARMTEL ARMT.665230.202-01, User Manual

Share
Download
ARMTEL ARMT.665230.202-01 User Manual Download Page 3

 DIS DIGITAL DESKTOP CALL STATION 

User Manual 

armtel.com

 

 

стр. 1/32  

[email protected] 

 

© Armtel

 

ENG 

INTRODUCTION 

This  User  Manual  is  intended  for  introducing  «DIS  Digital  Desktop  Call  Station» 

ARMT.665230.202  including  versions  of  ARMT.665230.202-01…ARMT.665230.202-03 
manufactured by Armtel LLC, Russia to the User. 

Digital desktop call station DIS is the subscriber's equipment of Public address and 

General alarm system within the digital communication systems DCN and IPN, manufactured 
by Armtel LLC, Russia, used at industrial and transportation facilities. 

DIS is installed in control rooms, offices, and premises. 

Short name of the product – DIS. 

Maintenance  personnel  for  DIS  shall  be  appointed  by  the  management  at  the 

installation  site.  The  maintenance  personnel  shall  be  required  to  know  the  operating 
procedure of DIS to the extent provided for by the User Manual. 

Duties of the maintenance personnel shall include maintenance of DIS by this User 

Manual. 

 

 

 

 

Summary of Contents for ARMT.665230.202-01





































Reviews:

No comments

Brands by name

Popular brands

Load more brands