SAFETY INFORMATION
■
DANGER: Risk of eye damage. Do not stare directly at the LED chips
of this LED strip.
■
CAUTION: Do not power LED tape while coiled on reel.
■
IMPORTANT: Always observe polarity for 24-volt connections,
+24V to +24V, –G to –G, –R to –R, –B to –B, –WW to –WW.
■
IMPORTANT: Do not install Class 2 low voltage wiring in the same runs
as AC main power. If AC and low voltage wires cross, keep them at
90-degree angles. Use only insulated staples, plastic ties, or wire
support clips to secure cords and wires.
■
NOTICE: LED flexible tape lighting rating: 24VDC 1A.
■
Only use the 24-volt LED lighting power supply which has been
provided with this kit.
■
Do not bend, crush or pull the cable. Protect from sharp edges,
oil and heat.
■
Electrical waste should not be disposed of with household waste.
Please recycle where facilities exist.
Two-year limited warranty
WHAT IS COVERED
The manufacturer warrants this fixture to be free from defects in materials
and workmanship for a period of two (2) years from date of purchase.
This warranty applies only to the original consumer purchaser and only
to products used in normal use and service. If this product is found to be
defective, the manufacturer’s only obligation, and your exclusive remedy, is
the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifications, alteration, neglect, or mishandling. This warranty
shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the
product as a result of an accident, misuse, abuse, negligence, alteration,
faulty installation, or any other failure not relating to faulty material or
workmanship. This warranty shall not apply to the finish on any portion of
the product, such as surface and/or weathering, as this is considered normal
wear and tear.
WHAT IS NOT COVERED
The manufacturer does not warrant and specifically disclaims any warranty,
whether expressed or implied, of fitness for a particular purpose, other than
the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/ expense costs involved in
the replacement or repair of said product.
Contact customer support at 410-354-6000, [email protected],
or visit armacostlighting.com/support.
Installation considerations
■
Where will you locate your power supply?
■
How will you run and conceal the wires to your LED tape lighting?
■
What is the best mounting position for the LED tape light to achieve
your desired effect?
■
See the section titled “Mounting options” for cabinet lighting
placement tips.
PACKAGE CONTENTS
Plug-in
power supply
RF receiver and 24 feet LED tape light (pre-assembled)
RF dimmer
remote
INSTALLATION
Connecting the LED tape and the adapter
This tape lighting kit comes fully assembled, but for ease of installation,
you may wish to temporarily disconnect the power adapter.
■
Unscrew the collar at the base of the adapter (A) where the output
cable exits.
■
When the collar is completely unscrewed, gently pull to remove the
cable.
■
Reverse these steps to reattach the output cable. The connector is
polarized, and can only be inserted in one orientation. Be sure all
connections are tight before powering on this tape light kit.
Cutting the tape to length
■
This tape light model can be cut every 12 LEDs, or about every 10 in.
Some of these intervals have copper pads (position A), and some
have silver solder joints (position B). Use sharp scissors to only cut in
the middle of either of these points.
Cut tape
at center of
copper pads
Okay to cut at silver
solder joints, but
do not use connector
1
INDOOR/OUTDOOR
Multi-Color/White LED Tape Light Kit
Item 624340
