manualshive.com logo in svg

ARM Prospector P1100, User Manual, Page: 80 / 154

Share
Download
ARM Prospector P1100 User Manual Download Page 80

Hardware Description

3-48

Copyright © ARM Limited 2000. All rights reserved.

ARM DUI 0122A

Note

To conserve power in the P1100 design the main power rail is +3V. This powers the 
3.3V parts at the limit of their standard tolerance.

3.15.4

Power switching

Several of the power supply outputs can be switched ON and OFF in the PLD power 
control register, as indicated in Table 3-22 on page 3-47. There are a number of control 
signals from other devices. These are:

POK

power OK signal. Provides the SA-1100 and keyboard controller 
as a power supply status flag.

PSU_BATT_OK

 

supplied to the keyboard controller. When deasserted the 
keyboard controller enters its CRITICAL SUSPEND mode. It 
exits CRITICAL SUSPEND when 

PSU_BATT_OK

 is asserted. 

PSU_VDD_FLT 

an inverted version of 

PSU_BATT_OK

 which is supplied to the 

SA-1100. When asserted the SA-1100 enters sleep mode.

PSU_LCD_BIAS

Yes

Maxim MAX686. 

Va14V to 20V Bias voltage for 
monochrome LCDs. 
Digitally controlled output ranging between 
+14V to +20V, controlled by setting either 
PLD_LCD_UP or PLD_LCD_DN in the 
LCD bias control register.
Switched ON and OFF by the PLD_S4_ON 
bit in the power control register.

EXP_+3V 

No

Regulator U37.

+3V alternate supply for the FPGA. The 
supply source is selected by using a link on 
header JP27.

EXP_+5V

No

Regulator U36.

Provided by a linear regulator from the 
ex9V source. This is the only source 
of power routed to the expansion connector 
JP20.

Table 3-22 Power supply rail usage (continued)

Name

Switched

Source

Usage

Summary of Contents for Prospector P1100



























































































































































Reviews:

No comments