ARM Musca-S1 Technical Reference Manual Download Page 47

Page: 47 / 194

3.2.2

Peripheral (expansion) region memory map

The Musca

‑

S1 test chip implements the Peripheral (expansion) region of the SSE

‑

200 memory map.

The following figure shows the Musca

‑

S1 test chip implementation of the Peripheral (expansion) region

of the SSE

‑

200 memory map.

0x4000_0000

Musca-S1 memory map

CMSDK Timer 0 (NS)

CMSDK Timer 1 (NS)

0x4000_1000

CMSDK Dual Timer (NS)

0x4000_2000

Message Handling Unit 0 (NS)

Message Handling Unit 1 (NS)

0x4000_3000

0x4000_4000

Reserved

0x4000_5000

Reserved

0x5000_0000

0x4008_0000

Non-secure Privilege control (NS)

0x4008_1000

Non-secure CMSDK Watchdog Timer

0x4008_2000

0x5000_1000

CMSDK Timer 0 (S)

CMSDK Timer 1 (S)

0x5000_2000

CMSDK Dual Timer (S)

Message Handling Unit 0 (S)

Message Handling Unit 1 (S)

0x5000_3000

0x5000_4000

Reserved

0x5000_5000

0x5008_2000

0x5008_0000

Security Privilege Control registers

0x5008_1000

Secure CMSDK Watchdog Timer

0x5008_3000

0x5008_4000

CMSDK Watchdog on 32KCLK

0x5002_E000

CMSDK Timer on 32KCLK

0x5002_F000

Reserved

0x5003_0000

0x5008_5000

Code

(AHB5 expansion)

SRAM

Peripheral

(expansion)

AHB5 expansion 0

AHB5 expansion 1

System

0x5008_6000

0x0000_0000

0x2000_0000

0x4000_0000

0x6000_0000

0x5008_7000

0x8000_0000

0xE000_0000

0xFFFF_FFFF

SSE-200 system memory map

CryptoCell-312

0x4008_8000

0x4008_C000

Reserved

0x5008_8000

0x5008_C000

System information register block

0x4002_0000

Reserved

0x4002_1000

CMSDK Timer on 32KCLK

0x4002_F000

Reserved

0x4003_0000

System Information registers (S)

0x5002_0000

System control registers (S)

0x5002_1000

Reserved (PPU units)

0x5002_2000

Reserved

0x5002_8000

Private core

0x4001_0000

Private core

0x5001_0000

Expansion 1

0x4010_0000

0x5010_0000

Reserved

SRAM 0 MPC (S)

SRAM 1 MPC (S)

Reserved

SRAM 2 MPC (S)

SRAM 3 MPC (S)

Reserved

CryptoCell-312

Expansion 1

Figure 3-2 Musca-S1 test chip memory map Peripheral region

3 Programmers model

3.2 Memory maps

101835_0000_01_en

reserved.

3-47

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands