ARM Musca-S1 Technical Reference Manual Download Page 154

Page: 154 / 194

Table 3-94 IOMUX_ALTF2_INSEL Register bit assignments

Bits

Name

Function

[31:0]

IOMUX_ALTF2_INSEL[31:0]

Selects either ALTF2_IN or ALTF3_IN as
destination of ALTF1 input multiplexer for
Musca

‑

S1 test chip multiplexed I/O

PA31

‑

PA0:

0b0

: Select ALTF3_IN.

0b1

: Select ALTF2_IN.

Reset value

0x0000_0000

Note

See

2.2.2 Test chip multiplexed I/O

on page 2-23

for the functions that are

available on the multiplexed Musca

‑

S1 test

chip I/O.

IOMUX_ALTF2_OUTSEL Register

The IOMUX_ALTF2_OUTSEL Register characteristics are:

Purpose

Selects either ALTF2_OUT or ALTF3_OUT as output data for Musca

‑

S1 test chip I/O

PA31

‑

PA0.

See

3.11.1 IOMUX registers

on page 3-122

for information on the Musca

‑

S1 test chip I/O

multiplexer.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the IOMUX_ALTF2_OUTSEL Register bit assignments.

Table 3-95 IOMUX_ALTF2_OUTSEL Register bit assignments

Bits

Name

Function

[31:0]

IOMUX_ALTF2_OUTSEL[31:0]

Main function output data select for Musca

‑

test chip multiplexed I/O PA31

‑

PA0:

0b0

: Select ALTF3_OUT.

0b1

: Select ALTF2_OUT.

Reset value

0xFFFF_FFFF

Note

See

2.2.2 Test chip multiplexed I/O

on page 2-23

for the functions that are

available on the multiplexed Musca

‑

S1 test

chip I/O.

IOMUX_ALTF2_OENSEL Register

The IOMUX_ALTF2_OENSEL_0 Register characteristics are:

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-154

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands