ARM Cortex-R4 Technical Reference Manual Download Page 16

Page: 16 / 436

Introduction

ARM DDI 0363G

1-4

ID073015

Non-Confidential

1.3

Features

The features of the processor include:

•

A dual-issue integer unit with integral CoreSight logic.

•

High-speed

Advanced Microprocessor Bus Architecture

(AMBA)

Advanced eXtensible

Interfaces

(AXI) for master and slave interfaces.

•

Dynamic branch prediction with a global history buffer, and a 4-entry return stack.

•

Low interrupt latency.

•

Non-maskable interrupt.

•

Optional

Floating Point Unit

(FPU). The Cortex-R4F processor is a Cortex-R4 processor

that includes the FPU.

•

A Harvard L1 memory system with:
—

optional

Tightly-Coupled Memory

(TCM) interfaces with support for error

correction or parity checking memories

—

optional caches with support for optional error correction schemes

—

optional ARMv7-R architecture

Memory Protection Unit

(MPU)

—

optional parity and

Error Checking and Correction

(ECC) on all RAM blocks.

•

The ability to implement and use redundant core logic, for example, in fault detection.

•

An L2 memory interface:
—

single 64-bit master AXI interface

—

64-bit slave AXI interface to TCM RAM blocks and cache RAM blocks.

•

A debug interface to a CoreSight

Debug Access Port

(DAP).

•

A trace interface to a CoreSight ETM-R4.

•

Performance Monitoring Unit

(PMU).

•

Vectored Interrupt Controller

(VIC) port.

Summary of Contents for Cortex-R4


















































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands

ARM Cortex-R4, Technical Reference Manual

Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands