ARM Cortex-M4 Generic User Manual Download | Manualshive

Page: 266 / 276

background image

Cortex-M4 Peripherals

ARM DUI 0553A

Copyright © 2010 ARM. All rights reserved.

4-50

ID121610

Non-Confidential

4.6.3

Floating-point Context Address Register

The FPCAR register holds the location of the unpopulated floating-point register space
allocated on an exception stack frame. See the register summary in

Cortex-M4F floating-point

system registers

for its attributes. The bit assignments are:

4.6.4

Floating-point Status Control Register

The FPSCR register provides all necessary User level control of the floating-point system. The
bit assignments are:

[2]

-

Reserved.

[1]

USER

0 = Privilege level was not user when the floating-point stack frame was allocated.
1 = Privilege level was user when the floating-point stack frame was allocated.

[0]

LSPACT

0 = Lazy state preservation is not active.
1 = Lazy state preservation is active. floating-point stack frame has been allocated but saving
state to it has been deferred.

Table 4-51 FPCCR register bit assignments (continued)

Bits

Name

Function

Table 4-52 FPCAR register bit assignments

Bits

Name

Function

[31:3]

ADDRESS

The location of the unpopulated floating-point register
space allocated on an exception stack frame.

[2:0]

-

Reserved. Read as Zero, Writes Ignored.

31

2

0

ADDRESS

3

Reserved

Reserved

DN

FZ

RMode

IOC

DZC

OFC

Reserved

UFC

IXC

IDC

N

31 30 29 28 27 26 25 24 23 22 21

8 7 6 5 4 3 2 1 0

Z C V

Reserved

AHP

Table 4-53 FPSCR bit assignments

Bits

Name

Function

[31]

N

Condition code flags. Floating-point comparison operations update these flags.

N

Negative condition code flag.

Z

Zero condition code flag.

C

Carry condition code flag.

V

Overflow condition code flag.

[30]

Z

[29]

C

[28]

V

[27]

-

Reserved.

«
...
264
265
266
267
268
...
»

Summary of Contents for Cortex-M4





















































































































































































































































































Reviews:

No comments

Related manuals for Cortex-M4

Brand: Cookworks Pages: 13

Brand: iMode Pages: 16

Brand: Broadata Pages: 16

Brand: CYP Pages: 12

Brand: Philips Pages: 3

Brand: Philips Pages: 44

Brand: Teesa Pages: 48

Brand: Excalibur Pages: 26

Brand: Waring Pages: 64

Brand: Lavry Pages: 31

Brand: Vitek Pages: 20

Brand: Scarlett Pages: 28

303919/20191015SZ259

Brand: ARENDO Pages: 80

Brand: EuroLite Pages: 10

Brand: Kalorik Pages: 52

Brand: QSC Pages: 20

Brand: Kambrook Pages: 36

Brand: Taurus Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands