ARM Cortex-M4 Page 136 Generic User Manual Download

Page: 136 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-89

ID121610

Non-Confidential

3.6.9

SMUAD and SMUSD

Signed Dual Multiply Add and Signed Dual Multiply Subtract.

Syntax

op{X}{

cond

}

where:

Is one of:

SMUAD

Signed Dual Multiply Add.

SMUADX

Signed Dual Multiply Add Reversed.

SMUSD

Signed Dual Multiply Subtract.

SMUSDX

Signed Dual Multiply Subtract Reversed.

is present, the multiplications are bottom × top and top × bottom. If the

omitted, the multiplications are bottom × bottom and top × top.

cond

Is an optional condition code, see

Conditional execution

on page 3-18

Specifies the destination register.

Rn, Rm

Are registers holding the first and the second operands.

Operation

The

SMUAD

instruction interprets the values from the first and second operands as two signed

halfwords in each operand. This instruction:
•

Optionally rotates the halfwords of the second operand.

•

Performs two signed 16 × 16-bit multiplications.

•

Adds the two multiplication results together.

•

Writes the result of the addition to the destination register.

The

SMUSD

instruction interprets the values from the first and second operands as two’s

complement signed integers. This instruction:
•

Optionally rotates the halfwords of the second operand.

•

Performs two signed 16 × 16-bit multiplications.

•

Subtracts the result of the top halfword multiplication from the result of the bottom
halfword multiplication.

•

Writes the result of the subtraction to the destination register.

Restrictions

In these instructions:
•

Do not use SP and do not use PC.

Condition flags

Sets the Q flag if the addition overflows. The multiplications cannot overflow.

Examples

SMUAD

R0, R4, R5 ; Multiplies bottom halfword of R4 with the bottom

; halfword of R5, adds multiplication of top halfword
; of R4 with top halfword of R5, writes to R0

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands