ARM Cortex-M4 Generic User Manual Download

Page: 128 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-81

ID121610

Non-Confidential

3.6.4

SMLAD

Signed Multiply Accumulate Long Dual.

Syntax

op{

}{

cond

}

;

where:

Is one of:

SMLAD

Signed Multiply Accumulate Dual

SMLADX

Signed Multiply Accumulate Dual Reverse

X specifies which halfword of the source register

is used as the multiply

operand. If

is omitted, the multiplications are bottom × bottom and top × top. If

is present, the multiplications are bottom × top and top × bottom.

cond

Is an optional condition code, see

Conditional execution

on page 3-18

Specifies the destination register.

Specifies the first operand register holding the values to be multiplied.

Specifies the second operand register.

Specifies the accumulate value.

Operation

The

SMLAD

and

SMLADX

instructions regard the two operands as four halfword 16-bit values. The

SMLAD

and

SMLADX

instructions:

•

is not present, multiply the top signed halfword value in

with the top signed

halfword of

and the bottom signed halfword values in

with the bottom signed

halfword of

•

Or if

is present, multiply the top signed halfword value in

with the bottom signed

halfword of

and the bottom signed halfword values in

with the top signed halfword

•

Add both multiplication results to the signed 32-bit value in

•

Writes the 32-bit signed result of the multiplication and addition to

Restrictions

Do not use SP and do not use PC

Condition flags

These instructions do not change the flags.

Examples

SMLAD

R10, R2, R1, R5 ; Multiplies two halfword values in R2 with

  ; corresponding halfwords in R1, adds R5 and writes to
  ; R10
SMLALDX R0, R2, R4, R6  ; Multiplies top halfword of R2 with bottom halfword
  ; of R4, multiplies bottom halfword of R2 with top
  ; halfword of R4, adds R6 and writes to R0.

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands