ARM Cortex-M4 Generic User Manual Download Page 106

Page: 106 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-59

ID121610

Non-Confidential

3.5.13

SSUB16 and SSUB8

Signed Subtract 16 and Signed Subtract 8.

Syntax

{

cond

}{

where:

Is any of:

SSUB16

Performs two 16-bit signed integer subtractions.

SSUB8

Performs four 8-bit signed integer subtractions.

cond

Is an optional condition code, see

Conditional execution

on page 3-18

Specifies the destination register.

Specifies the first operand register.

Specifies the second operand register.

Operation

Use these instructions to change endianness of data:

The

SSUB16

instruction:

Subtracts each halfword from the second operand from the corresponding
halfword of the first operand.

Writes the difference result of two signed halfwords in the corresponding
halfword of the destination register.

The

SSUB8

instruction:

Subtracts each byte of the second operand from the corresponding byte of
the first operand

Writes the difference result of four signed bytes in the corresponding byte
of the destination register.

Restrictions

Do not use SP and do not use PC

Condition flags

These instructions do not change the flags.

Examples

SSUB16 R1, R0 ; Subtracts halfwords in R0 from corresponding halfword of R1
; and writes to corresponding halfword of R1
SSUB8

R4, R0, R5

; Subtracts bytes of R5 from corresponding byte in

; R0, and writes to corresponding byte of R4.

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Brands by name

Popular brands