ARM Cortex A9 Technical Reference Manual Download Page 203

Page: 203 / 213

Cycle Timings and Interlock Behavior

ARM DDI 0388I

B-8

ID073015

Non-Confidential

B.5

Branch instructions

Branch instructions have different timing characteristics:

•

Branch instructions to immediate locations do not consume execution unit cycles.

•

Data-processing instructions to the PC register are processed in the execution units as
standard instructions. See

Data-processing instructions

on page B-3

•

Load instructions to the PC register are processed in the execution units as standard
instructions. See

Load and store instructions

on page B-4

See

About the L1 instruction side memory system

on page 7-5

for information on dynamic

branch prediction.

Summary of Contents for Cortex A9





















































































































































































































Search results

Summary of Contents for Cortex A9

Reviews:

Related manuals for Cortex A9

Brands by name

Popular brands

ARM Cortex A9, Technical Reference Manual

Search results

Summary of Contents for Cortex A9

Reviews:

Related manuals for Cortex A9

Brands by name

Popular brands