ARM ARM9TDMI Technical Reference Manual Download

Page: 49 / 154

ARM9TDMI Coprocessor Interface

ARM DDI0145B

4-13

4.5

CDP

CDP signals normally execute in a single cycle. Like all the previous cycles,

InMREQ

is driven LOW to signal when an instruction is entering the decode and then the execute
stage of the pipeline:

•

if the instruction really is to be executed, the

PASS

signal is be driven HIGH

during phase 2 of execute

•

if the coprocessor can execute the instruction immediately it drives

CHSD[1:0]

with LAST

•

if the instruction requires a busy-wait cycle, the coprocessor drives

CHSD[1:0]

with WAIT and then

CHSE[1:0]

with LAST.

Figure 4-5 on page 4-14 shows a CDP which is cancelled due to the previous instruction
causing a data abort. The CDP instruction enters the execute stage of the pipeline and
is signalled to execute by

PASS

. In the following phase

LATECANCEL

is asserted.

This causes the coprocessor to terminate execution of the CDP instruction and for it to
cause no state changes to the coprocessor.

Summary of Contents for ARM9TDMI











































































































































Search results

Summary of Contents for ARM9TDMI

Reviews:

Related manuals for ARM9TDMI

Brands by name

Popular brands

ARM ARM9TDMI, Technical Reference Manual

Search results

Summary of Contents for ARM9TDMI

Reviews:

Related manuals for ARM9TDMI

Brands by name

Popular brands