ARM ARM9TDMI Technical Reference Manual Download

Page: 32 / 154

ARM9TDMI Processor Core Memory Interface

3-10

ARM DDI0145B

3.5

Unidirectional/bidirectional mode interface

The ARM9TDMI supports connection to external memory systems using either a
bidirectional data data bus or two unidirectional buses. This is controlled by the

UNIEN

input.

UNIEN

is LOW,

DD[31:0]

is a tristate output bus used to transfer write data. It is only

driven when the ARM9TDMI is performing a write to memory. By wiring

DD[31:0]

the input

DDIN[31:0]

bus (externally to the ARM9TDMI), a bidirectional data data bus

can be formed.

UNIEN

is HIGH, then

DD[31:0]

, and all other ARM9TDMI outputs, are

permanently driven.

DD[31:0]

then forms a unidirectional write data data bus. In this

mode, the tristate enable pins

IABE

DABE

DDBE

TBE

, and the TAP instruction

nHIGHZ

, have no effect. Therefore all outputs are always driven.

All timing diagrams in this manual, except where tristate timing is shown explicitly,
assume

UNIEN

is HIGH.

Summary of Contents for ARM9TDMI











































































































































Search results

Summary of Contents for ARM9TDMI

Reviews:

Related manuals for ARM9TDMI

Brands by name

Popular brands

ARM ARM9TDMI, Technical Reference Manual

Search results

Summary of Contents for ARM9TDMI

Reviews:

Related manuals for ARM9TDMI

Brands by name

Popular brands