ARM ARM9TDMI Technical Reference Manual Download | Manualshive

Page: 141 / 154

background image

ARM9TDMI Signal Descriptions

ARM DDI0145B

Copyright © 1998, 1999 ARM Limited. All rights reserved.

A-3

A.2

Data memory interface signals

Table A-2 Data memory interface signals

Name

Direction

Description

DA[31:0]

Output

Data Address Bus. This is the processor data address bus. It changes when

GCLK

is

HIGH.

DABE

Input

Data Address Bus Enable. When LOW, this input puts the data address bus,

DA[31:0]

,

drivers into a high impedance state. This signal has the same effect on

DnTRANS

,

DLOCK

,

DMAS[1:0]

,

DnRW

, and

DnM[4:0]

. If

UNIEN

is HIGH this signal is

ignored.

DABORT

Input

Data Abort. This input allows the memory system to tell the processor that the
requested data memory access is not allowed.

DD[31:0]

Output

Data Output Bus. This output bus is used to transfer write data between the processor
and external memory. The output data will become valid during phase 1 and remain
valid through

GCLK

phase 2.

If UNIEN is LOW, this is a tristate output bus and is only driven during write cycles.

If UNIEN is HIGH, this bus is always driven.

DDBE

Input

Data Data Bus Enable. This is an input which, when LOW, puts the Data Data Bus

DD[31:0]

into a high impedance state. If

UNIEN

is HIGH this signal is ignored.

DDEN

Output

Data Data Bus Output Enabled. This signal indicates when the processor is
performing a write transfer on the Data Data Bus,

DD[31:0]

.

DDIN[31:0]

Input

Data Input Bus. This input is used to transfer load data between external memory and
the processor. It should be driven with the requested data by the end of

GCLK

phase

2.

DLOCK

Output

Data Lock. If HIGH at the end of

GCLK

phase 2, any data memory access in the

following cycle is locked, and the memory controller must wait until

DLOCK

goes

LOW before allowing another device to access memory.

DMAS[1:0]

Output

Data Memory Access Size. These outputs encode the size of a data memory access in
the following cycle. A word access is encoded as 10 (binary), a halfword access as 01,
and a byte access as 00. The encoding 11 is reserved.

DMORE

Output

Data More. If HIGH at the end of

GCLK

phase 2, the data memory access in the

following cycle will be directly followed by a sequential data memory access.

DnM[4:0]

Output

Data Mode. The processor mode within which the data memory access should be
performed.

Note that the data memory access mode may differ from the current processor mode.

«
...
139
140
141
142
143
...
»

Summary of Contents for ARM9TDMI



























































































































































Reviews:

No comments

Related manuals for ARM9TDMI

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

Linear SCP-LT8362-S-EVALZ

Brand: Analog Devices Pages: 8

Brand: Cytron Technologies Pages: 13

Brand: IEI Technology Pages: 3

Brand: Eneo Pages: 68

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

Brand: ETAS Pages: 82

Brand: Hauppauge Pages: 55

Brand: NCR Pages: 15

Brand: VIA Technologies Pages: 2

Brand: Trend Micro Pages: 2

Brand: TECO Pages: 24

Brand: Intel Pages: 469

Brand: ICP DAS USA Pages: 8

Brand: Adeunis RF Pages: 68

Brand: StarTech.com Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands