background image

DUAL HALOGEN FLOODLIGHTS WITH TRIPOD (HL21)

ASSEMBLY

DO’S AND DON’TS

OPERATION:

 The Dual Halogen Floodlight HL21 is suitable for indoor or outdoor use, 

from any standard power point and is weatherproof to IP54

Extreme care should be taken when handling and operating the dual Halogen Floodlight 

HL21. Please observe the following do’s and don’ts to ensure safe and trouble free use:

DO

  ensure combustible material is kept away from Floodlight.

DO

  use the handle (A) to adjust the beam.

DO

  keep the floodlight out of reach of children when in use.

DO

  switch off and allow to cool for a minimum of 10 minutes before storing.

DO

  ensure that tripod is standing vertically on a stable surface.

DO

  take extreme care in crowded or confined areas that tripod is not positioned 

where it can be easily toppled over.

DO

  weigh down base of tripod with sandbags for extra stability if necessary. ie. one or 

more plastic bags filled with sand, then tied to pole or tripod legs.

DO

  use the Floodlights in horizontal position (+4°). If not used in  

horizontal position the tube life will be greatly reduced.

DON’T

 

 operate if the front glass safety shield is broken. Replace with correct 

tempered glass only.

 

DON’T

  touch tube with bare hands. This could cause tube to shatter  

when Floodlight is switched on.

DON’T

  stand Floodlight in pools of water.

DON’T

  handle with wet hands or operate when standing on wet surface.

DON’T

  position the Floodlight closer than one metre from surface to be illuminated.

DON’T

  allow power cable to come into contact with front of Floodlight or housing.

DON’T

  touch the housing or glass while hot.

DON’T

  allow overhanging shrubs or foliage to come into contact with Floodlight.

DON’T

  place or operate the Floodlight closer than 5 metres to a swimming pool or 

spa.

DON’T

  operate the Floodlight with the front of housing opened.

To assemble stand, loosen locking knob, 

then push down black locking bracket 

until tripod legs are fully extended. 

Tighten locking knob. Always keep the 

centre telescopic pole vertical for 

stability and safety.
Attach Floodlight  

handle (A) and tighten wingnut (B). 
Next mount the cross bar onto the 

tripod, then fit the floodlights to the 

crossbar using the screws and 

threaded knobs provided.
Fix the "Y" junction of the power cord by 

using the screw at the centre side face 

of the crossbar.
The pole may be raised by loosening 

the locking ring and extending the 

sections. Tighten locking ring to hold in 

place. Full height is approximately 1.8m.

The tungsten halogen tube is supplied and packed separately to avoid damage. Open the 

Floodlight housing by loosening the top screw. The glass front of the housing will hinge 

forward and down. Ensure that Floodlight is unplugged from wall socket. Insert the tube 

in the holder, ensuring that you do not touch the glass envelope of the tube with bare 

hands. Use the tube wrapper to handle tube. Check that the tube is seated correctly on 

the holder contacts. 

(Oils from the hands can cause the tube to fail or shatter).  

If necessary the tube should be carefully cleaned with methylated spirit and dried 

before installation. Do not attempt to adjust or force the tube holder with tools, but 

carefully push the tube into the holder contacts. Reassemble the Floodlight housing.

A

B

FITTING THE TUNGSTEN HALOGEN TUBE

Tighten locking rings to 

hold in place. 

Push down 

black locking 

bracket until 

tripod legs are 

fully extended. 

2

3

Reviews: