Arjo Huntleigh Sonicaid Team3 USA Instructions For Use Manual Download

Page: 36 / 84

Instructions For Use

5.5 Switching the Unit OFF

Press and hold

to switch the unit Off. A confirmation screen will be displayed.

Power Off

Touch Power Off to turn off the Team3 or touch

to return to the last screen.

Alternatively, continued holding of the off button for ~15s will switch the unit off directly from any machine state.

5.6 Battery Charging

If the following conditions are all true,

•  The unit is switched OFF
•  The unit is connected to the mains supply
•  The battery option is installed
•  The battery is not fully charged

then the On/Off button will illuminate green

and flash, indicating that the battery is charging.

Otherwise the indicator will be OFF.

Note

Typical charge time to 90% capacity from discharged is 3 hours.

Note

With Battery supply, monitoring a single ultrasound channel at 25% volume and no printing, Team3

can operate for a minimum of 4 hours.

Summary of Contents for Huntleigh Sonicaid Team3 USA





















































































Search results

Summary of Contents for Huntleigh Sonicaid Team3 USA

Reviews:

Related manuals for Huntleigh Sonicaid Team3 USA

Brands by name

Popular brands

Arjo Huntleigh Sonicaid Team3 USA, Instructions For Use Manual

Search results

Summary of Contents for Huntleigh Sonicaid Team3 USA

Reviews:

Related manuals for Huntleigh Sonicaid Team3 USA

Brands by name

Popular brands