Arizona Instrument JEROME 431-X Operation Manual Download Page 28

Page: 28 / 56

AZI Customer Service 800-528-7411 or 602-470-1414

Page 28 of 56

Instrument I/O Interface

The 431-X I/O port (25 pin D-sub) provides the following functions:

•

Serial data communication



Interface type: RS-232C full duplex, DCE



Parameters: 1200 Baud, 1 start bit, 8 data bits, 2 stop bits, no parity



Pin assignments:

Pin 1

Protective ground

Pin 2

Data in

Pin 3

Data out

Pin 7

Data ground

•

Switched battery connection for Data Logger



Pin assignments:

Pin 9

Battery (+)

Pin 7

Battery ground (-)

Pin 23

Battery ground (-)

•

Unswitched battery connection for external battery pack pin assignments



Pin assignments:

Pin 15

Battery (+)

Pin 19

Battery (+)

Pin 7

Battery ground (-)

Pin 23

Battery ground (-)

NOTE:

Pins 6, 8, 11, 17, 18, 20 and 21 are non-standard and should not be connected.

Summary of Contents for JEROME 431-X

























































Search results

Summary of Contents for JEROME 431-X

Reviews:

Brands by name

Popular brands

Arizona Instrument JEROME 431-X, Operation Manual

Search results

Summary of Contents for JEROME 431-X

Reviews:

Brands by name

Popular brands