Ariterm Vedo, Installation, Operation And Maintenance Manual

Page: 21 / 28

21
OPERATING MENUS
Even if the loading pump is switched ON , it
will not rotate if the boiler water temperature
is below the pump starting temperature (Set-
ting- Tank pump start). You can test the fan
and pump operation in the Testing menu .
Select Menues and press the arrow right but-
ton to access the main menu, which has the
sub-menus Service, Settings and Testing
Move to the previous menu by pressing the
left arrow button. If no button has been
activated for one minute, the view returns to
the main screen.
Service - menu
The setting on the Service menu are important
as they are used to set the operating mode
Operation mode . The factory setting is bur-
ning wood Wood . When you want to operate
the fan through the pellet burner, select Pellet .
NOTE: The operating mode selection must
be done within a minute of switching the
control unit on.
When you want to use the Tank pump fun-
ction, make sure the correct line is switched
ON . When this setting has been selected, the
main screen displays accumulator and pump
icons. The loading pump settings also appear
in the Settings menu . The boiler temperature
sensor can be switched on regardless of whet-
her the loading pump is being used or not.
The bottom line of the Service menu displays
the language used. You can select from Fin-
nish, Swedish and English.
Settings menu (Wood burning
mode)
In time and temperature settings, one press
of the button adds one unit to the figure. For
faster resetting, keep the button pressed and
the figure will change faster.
When you have selected Wood in the Service
menu , the following are displayed in the
Settings menu:
Fan temp. limit determines the flue gas
temperature at which the fan switches off.
Factory setting 90 °C. This temperature can
be set between 70 and 150 °C. When flue gas
temperature is over that limit, fan will inn.
Testing
Fan
Tank pump
T1
T2
55%
ON
30°C
22°C
Settings WOOD
Fan temp. limit
Fan / delay time
Fan speed
Tank pump starts
No 90°C
10min
55%
80°C
90°C
Settings PELLET
Fan speed / max
Fan speed / min
Pump temp. limit 50%
30%
70%
MENUES
Service
Settings
Testing
Fan
Smokegas temp
Tank pump
Boiler water
Menues
ON
24°C
ON
21°C
Service
Operation mode
Tank pump
Boiler t.sensor
English WOOD
ON
ON
T1
T2
ON
T1
T2
22
°C
27
°C
(+)
0%
Testing
Fan
Tank pump
T1
T2
55%
ON
30°C
22°C
Settings WOOD
Fan temp. limit
Fan / delay time
Fan speed
Tank pump starts
No 90°C
10min
55%
80°C
90°C
Settings PELLET
Fan speed / max
Fan speed / min
Pump temp. limit 50%
30%
70%
MENUES
Service
Settings
Testing
Fan
Smokegas temp
Tank pump
Boiler water
Menues
ON
24°C
ON
21°C
Service
Operation mode
Tank pump
Boiler t.sensor
English WOOD
ON
ON
T1
T2
ON
T1
T2
22
°C
27
°C
(+)
0%
Testing
Fan
Tank pump
T1
T2
55%
ON
30°C
22°C
Settings WOOD
Fan temp. limit
Fan / delay time
Fan speed
Tank pump starts
No 90°C
10min
55%
80°C
90°C
Settings PELLET
Fan speed / max
Fan speed / min
Pump temp. limit 50%
30%
70%
MENUES
Service
Settings
Testing
Fan
Smokegas temp
Tank pump
Boiler water
Menues
ON
24°C
ON
21°C
Service
Operation mode
Tank pump
Boiler t.sensor
English WOOD
ON
ON
T1
T2
ON
T1
T2
22
°C
27
°C
(+)
0%