ARIS Tensor Zone 2/22 Manual Download Page 40

Page: 40 / 44

Tensor

Error messages
If the 7-segment display is present, error messages occur according to the table below. Automatic and manual operation can not be
used as long as a fault is present. The set-up can be started.

Display

Function

Meaning

Remarks

Motor Error

No valid values for motor control

from Hall sensor

Please contact your responsi-

ble ARIS contact person

Sensor Error

No valid values from position sensor.

No existing magnet or out of valid range

Please contact your responsi-

ble ARIS contact person

Range Error

Programmed end positions too close

End positions must be

> 0.5 sensor turns (corre-

sponding 28°) apart

Calibration Error

Actual output value too low

Set input value too low

Please contact your responsi-

ble ARIS contact person

Sensor Fault

Correlation error, not correctable

Disconnect power supply.

After re-energizing the error

should not be displayed.

Parameter Error

Too low difference between

free set and actual values

At free values, the difference

must cover at least 20% of

the complete range

Stall Error

Standstill or blockade of the motor

Please contact your responsi-

ble ARIS contact person

Wire break

Wire break detection caused message

Examine control lines and

clamps

EEprom Error

Fault in EEPROM Data, inconsistent data,

operation no longer possible

Please contact your responsi-

ble ARIS contact person

Summary of Contents for Tensor Zone 2/22













































Search results

Summary of Contents for Tensor Zone 2/22

Reviews:

Related manuals for Tensor Zone 2/22

Brands by name

Popular brands

ARIS Tensor Zone 2/22, Manual

Search results

Summary of Contents for Tensor Zone 2/22

Reviews:

Related manuals for Tensor Zone 2/22

Brands by name

Popular brands