Ariens 911086 Owner'S/Operator'S Manual Download Page 4

GB - 5

5. Instruct customer on controls and 

operation of unit. Discuss and emphasize 
the Safety Rules. Give customer 
Owner/Operator, Parts, and Engine 
manuals. Advise customer to thoroughly 
read and understand them.

DISCLAIMER

Ariens reserves the right to discontinue, make 
changes to, and add improvements upon its 
products at any time without public notice or 
obligation.The descriptions and specifications 
contained in this manual were in effect at 
printing. Equipment described within this 
manual may be optional. Some illustrations 
may not apply to your unit.

SAFETY ALERTS

Look for these symbols to point out 
important safety precautions. They 
mean:

Attention!

Personal Safety Is Involved!

Become Alert! 

Obey The Message!

The safety alert symbols above and signal 
words below are used on decals and in this 
manual.

Read and understand all safety messages.

NOTATIONS

NOTE:  General reference information for 
proper operation and maintenance practices.

IMPORTANT: Specific procedures or 
information required to prevent damage to unit 
or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working 
precautions, for the benefit of yourself and 
others. Understand and follow all safety 
messages. Be alert to unsafe conditions and 
the possibility of minor, moderate, or serious 
injury or death. Learn applicable rules and 
laws in your area.

REQUIRED OPERATOR TRAINING

Original purchaser of this unit was instructed 
by the seller on safe and proper operation. If 
anyone other than the original purchaser will 
use the unit, ALWAYS provide this manual and 
any needed safety training before operation.

SAFETY

WARNING: This cutting machine 
is capable of amputating hands 
and feet and throwing objects. 
Failure to observe the safety 
instructions in the manuals and 
on decals could result in serious 
injury or death.
Slopes are a major factor related 
to slip and fall accidents. 
Operation on all slopes requires 
extra caution.

Tragic accidents can occur if the 
operator is not alert to the 
presence of children. Never 
assume that children will remain 
where you last saw them.
Gasoline is extremely flammable 
and the vapors are explosive, 
handle with care.

Stop unit and engine and allow 
moving parts to stop before 
leaving operator’s position.

DANGER: IMMINENTLY 
HAZARDOUS SITUATION! If not 
avoided, WILL RESULT in death or 
serious injury.

WARNING: POTENTIALLY 
HAZARDOUS SITUATION! If not 
avoided, COULD RESULT in death 
or serious injury.

CAUTION: POTENTIALLY 
HAZARDOUS SITUATION! If not 
avoided, MAY RESULT in minor or 
moderate injury. It may also be used 
to alert against unsafe practices.

Summary of Contents for 911086























Reviews: