manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

29 Appendix

388

ARGUS 152

H) General Error Messages 

Prot. not supp.

Unknown error

No PPP connec.

Test aborted

Ping start error

Fault: PPP con-
nection

Unexp. PING end

Display on ARGUS

Description

The protocol (IP, PPPoE, etc.) is not supported in the selected 
mode.

Unknown error occurred.

No PPP connection can be setup. 

Test aborted by user.

Error when starting the Ping test.

Unexpected termination of the PPP connection.

Unexpected termination of the Ping test.

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Linksys WRT54G3G-AT Product Data preview
WRT54G3G-AT
Brand: Linksys Pages: 2
Idis DR-8432 Installation Manual preview
DR-8432
Brand: Idis Pages: 31
Patton electronics SMARTNODE 4552 Getting Started Manual preview
SMARTNODE 4552
Brand: Patton electronics Pages: 65
NetBurner MOD5272 Quick Start Manual preview
MOD5272
Brand: NetBurner Pages: 15
Genie WONVR216P5 Quick Start Manual preview
WONVR216P5
Brand: Genie Pages: 15
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Zonet ZSR4134WS User Manual preview
ZSR4134WS
Brand: Zonet Pages: 53
BWI PCI Duo/TP User Manual preview
PCI Duo/TP
Brand: BWI Pages: 5
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
LevelOne NVR-0432 User Manual preview
NVR-0432
Brand: LevelOne Pages: 142
ORiNG IES-3082GC User Manual preview
IES-3082GC
Brand: ORiNG Pages: 101
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Brand: Avocent Pages: 2
Axis P1355-E User Manual preview
P1355-E
Brand: Axis Pages: 64
SHOWTEC LED Operator 4 Manual preview
LED Operator 4
Brand: SHOWTEC Pages: 15
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Brand: ACTi Pages: 12
U-Media WST-375L User Manual preview
WST-375L
Brand: U-Media Pages: 42

Brands by name

Popular brands

Load more brands