manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 273

19 Operation on an ISDN Access

ARGUS 152 

273

Time Measurement

B channel delay

The ARGUS will measure the delay on the selected B channel. If the ARGUS does not 
receive the data back in the B channel in about 13 seconds, it will display the message “No 
loop”. The measurement (continuous measurement) must be terminated manually.

ARGUS - Main Menu

First press 

<Delete>

 and enter the B 

channel on the keypad, or use the cursor 
keys to set it.

Perform measurement

Display:

The measurement will be repeated in 
cycles (continuous measurement).

avg:

average B channel delay

min:

shortest B channel delay

max: longest B channel delay

bit:

The average B channel delay in bits 
(multiples of the time required to 
send a bit at 64 kbit/s, it takes 15.26 
µs to send a bit).

Stop measurement, the ARGUS will 
display the last measurement.

Single tests

Time measurement

B channel select

B channel delay

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands