manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 236

19 Operation on an ISDN Access

236

ARGUS 152 

Automatic X.31 Test
D channel

The “automated X.31 Test in D channel“ consists of two steps:

ARGUS Main Menu.

Select the profile.

Start test

The test can take up to 4 minutes.

The ARGUS will display the currently 
tested TEI, the previously tested TEI and 
the results:

First step:

The ARGUS tests whether it is possible to access the X.25 service via the 
D channel on the ISDN access under test. The ARGUS sequentially 
checks all the TEIs from 0 to 63. All the TEIs with which the X.31 service is 
possible on Layer 2 will be displayed.

Second 
step:

For each TEI with which X.31 is possible on Layer 2, a "CALL_REQ" 
packet will be sent and then the ARGUS will wait for an answer. 
Beforehand, the ARGUS will request the entry of the X.25 access number, 
which will be saved in speed-dialling memory under X.31 test number (see 
page 364). With the entry of the X.25 access number, you can - if you wish 
- select a logical channel (LCN) other than the default.

<Edit>

Change to the profile parameters 
(see page 233).

The parameters can be edited.

OK

NOK

= X.31 is available for this TEI

= X.31 is not available for this 

   TEI 

Single tests

X.31 Test

D channel

Automatic

X.31 profile 1

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands