manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

19 Operation on an ISDN Access

210

ARGUS 152 

The "IP / L3" LED will light after the ARGUS has setup Layer 3. At the same time the 
ARGUS will start a B channel test and then display the results. If an error occurs in the 

B channel test (e.g. access is not plugged-in), the ARGUS will display an error message 
(see appendix). The ARGUS will then idle in the State display:

Display:

If only one B channel is available, this can have an impact on the service check 
and the testing of the supplementary services.

- Type of access (in the example, BRI S/T)
- Access Mode

NTs 

NTm 

TEs 

TEm

NT Simulation Slave (see L1

page 213)

NT Simulation Master L1

TE Simulation Slave L1

TE Simulation Master L1

- Bus configuration

D channel Layer 2 mode

P-P

P-MP

Point-to-point

Point-to-multipoint

- D channel protocol

in the example, DSS1

- The availability of the B channels

B12

B1-

B-2

B--

Both channels are available 

Only B channel 1 is available 

Only B channel 2 is available

No B channel is available

Example:

ARGUS State Display on a BRI access

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

D-Linke DHP-346AV Quick Installation Manual preview
DHP-346AV
Brand: D-Linke Pages: 32
Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
C&H Technologies EM405-8 Manual preview
EM405-8
Brand: C&H Technologies Pages: 46
Rain Bird E-3 Installation, Programming & Operation Manual preview
E-3
Brand: Rain Bird Pages: 17
Caimore CM520-86EG User Manual preview
CM520-86EG
Brand: Caimore Pages: 79
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Brand: IEI Technology Pages: 2
Xantech CC62 Installation Instructions preview
CC62
Brand: Xantech Pages: 5
Billion BiPAC 5200S RC Series User Manual preview
BiPAC 5200S RC Series
Brand: Billion Pages: 79
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
TRENDnet TEG-S16R - DATA SHEETS Quick Installation Manual preview
TEG-S16R - DATA SHEETS
Brand: TRENDnet Pages: 12
M86 Security IR Web Filter User Manual preview
IR Web Filter
Brand: M86 Security Pages: 540
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Brand: ATEN Pages: 178
Icy Box IB-NAS902 User Manual preview
IB-NAS902
Brand: Icy Box Pages: 17
Sarian Systems DR 6410 Installation Manual preview
DR 6410
Brand: Sarian Systems Pages: 9
Lobaro wMBUS-LoRaWAN User Manual preview
wMBUS-LoRaWAN
Brand: Lobaro Pages: 26

Brands by name

Popular brands

Load more brands